here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi
I am planning to use NRF51822. Have not used these parts yet.
I have 4 peripherals and 1 central hub. All communicating in BLE. And central hub will also connect to...
In our project we are using the nrf51822. We planned to connect an external flash for storage purposes. While coding the software I got the advice to give special attention...
Hi,
I use nRF51822.
Can it judge a UID of higher RSSI level by comparing the RSSI of two advertizers with Central mode in nRF51882?
I want to know a UID of advertiser...
Hi, I use
nRF51822 Rev.3, SDK 7.2, SDK 10.0, S110 8.0, and S120 2.1 most of the time.
I mostly quote most of the codes from the SDK's examples such as HID keyboard or...
Hi all,
We have a issues with the SPI communication and hope someone could help us.
Using SDK 8.0.0 and Soft Device S110 8.0.0
code process step:
enable ble...
Hi
I am investigating some weird issue where a device sometimes locks up: it is BLE connected to my iphone app, and then I bombard it with writes to a specific characteristic...
Hi everyone,
We are on the lookout for a bluetooth module from Nordic that is suitable for our product. The product is a handheld digital stethoscope that transfers acquired...
I am building my application up on the ant_scalable_encrypted_tx example. I want to use RTC too, for that I took an example code off of the rtc example.
The problem is...
Hello.
I use s130 2.0.0-7.alpha stack and thus app starts at 0x1B000
Questions:
How to change default app start address, for example to 0x25000 ?
How...
I'm using the nrf51822 EK board (pca10001). I'm able to connect fine from my laptop (using Bluez) if I use a random address on my laptop. However, if I use a public address...
I am new to Nordic Evaluation Kit.
I am working in Nordic nrf51822 (PCA10001) Evaluation board.
Following are my setup.
OS : Ubuntu 14.04 64 bit.
SDK : nRF5_SDK_11...
Hi all,
I need to know the RSSI Value (distance) between my nRF 51 DK and my connected device (iOS Device). I made these code changes:
switch (p_ble_evt->header.evt_id...
Hello!
I've been using RTT viewer to view some data in my nRF52832. Everything works fine but I am unable to clear the RTT viewer terminal screen.
As it is in the manual...
Hi,
I am trying to get the experimental NFC example "HR with pairing over NFC" to work.
I can read the tag correctly with an android phone : the NDEF message is correct...
Dear All：
My NRF24L01+ use Dynamic PayLoad,What register need configure NRF51822?
NRF24L01+ Configuration as follow:
SPI_RW_Reg(WRITE_REG + DYNPD, 0x01);//Enable...
