I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi. i'm using PCA10028, SDK10.0.0, S130.
I want to check RF characteristics.
nRf51 should make RF Tx continuously.
I think there is example source code for that.
Which...
The function dm_ble_evt_handler has codes like this.
void dm_ble_evt_handler(ble_evt_t * p_ble_evt){ // from device_manager_peripheral.c
switch (p_ble_evt->header...
Hello,
I have develop and app to send BLE Advertisement packet in Android. But what I found out is my device has Android Lollipop but it does not have peripheral mode turned...
I am using the nRF52 Preview board, PCA 10036. I need to provide a high-frequency clock signal to a peripheral. Anything between 1 and 4 MHz will work. However, I don't need...
I currently call nrfjprog twice to flash the softdevice hex and then the app hex separately. But as I am using two nrfjprog calls, I am unable to set --rbp ALL with the second...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hi there,
Currently, I am working on a project which uses iphone(or other IOS device) as a central, and nrf51822 as peripheral.
Basically, the concept is that peripheral...
itg3200.rar hello there i have interfaced itg3200 with nrf51 dk. but now i want to see it on oscilloscope. can you help me?? i have put my scope's screen shot and code here...
HI all,
We've recently moved to SDK 11.0 and it certainly has not been a painless migration, especially when using GCC.
Setup: GCC 5.2.1 on Linux Mint with nrf51 xxAA...
Hi, I'm wonder it is possible to stream video using nRF52x family? I know that chipset isn't designed to this purpose, but I'm only wonder about that.
Thanks
Robert
Hi,
I've started using the nRF5 11.0.0 (89a8197) SDK on a board that does not include an external low-frequency CLK source.
When using the nRF52 0.9.2 SDK, we were recommended...
I want to reserve a section of memory, FLASH, that will hold static, read only, product data. My application makes use of the following parts of the Nordic ecosystem.
...
I would like to carry out communication with a plurality of peripheral using a central multi-link function.
When performing the communication via the relay unit, the communication...
Hi ,
I'm intrested in using the BLE UART apllication provided by Nordic for the nRF51 422 developpement kit and I have a little question to ask and please forgive its simplicity...
Environment is a PCA10040 v1.1.0, measuring current with a Rigol DS1104B over a 10 Ohm resistor.
I'm using the ble_pwr_profiling example from nRF5 SDK v11. I've programmed...
