Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
A good problem to have... we're only seeing 300nA current draw with a 3V lithium primary while in SystemOFF on the nRF51822, using LDO.
Is that correct? We've measured...
HI , ALL
i added a event in the function 'on_ble_evt' like followings:
case BLE_GAP_EVT_ADV_REPORT:
printf("Start Advertising\r\n");
break;
At first i think...
Hi, I mostly use the SDK 7.2 or SDK 10 and S110 7.1 or 8.0
since I have multiple custom boards that uses revision 2 and 3 chips.
My custom board I'm about to use has...
I want get an interrupt from the ADC after every sample (oversampled by 4, so burst is enabled). This works fine with EasyDMA, but I want to be able to not use the EasyDMA...
Is there some documentation somewhere to explain how these work?
I kinda understand but in app_timer, why use a software interrupt of the same priority as the RTC interrupt...
In my project, the nrf51422 chip will be hosted on a board with another CPU. I need to be able to flash the firmware through the SWD interface, controlled by the host CPU...
Hello,
I have a running system powered by ARM Cortex-M3 (LPC1343 MCU) and I want to add bluetooth through nRF51822 usb dongle.
I want to send some data from LPC1343...
Hi,
I try to send a string using example code ble_app_uart_pca10028 without input from terminal
,but directly from inside the code
All of the tutorials I've search...
hello there i want to interface adxl345 with nrf51822 using SPI interface i am new to spi. i am using spi master with spi slave example. i want to write 0x08 in 0x32 register...
I want to debug RF51822 board by uart port , communicate with pc, e.g use printf() in program,after download RF51822 board,print statement to pc uart port, how to realize...
I am trying to use my nRF52-DK with Yggdrasil.
I took example from here: *\nRF5_SDK_11.0.0_89a8197\examples\ble_central_and_peripheral\ble_connectivity\pca10040\ser_s132_uart...
Hi, I was able to successfully implement the tutorial titled "Testing and using a simple BLE application" available in the Tutorial section and transfer data from termite...
Using OBS-421 from Connectblue as Central. Using simple AT command to connect and get data. Can connect successfully with Cypress BLE as well as the TI sensortag and get data...
Hello,
When i have a bootloader installed and i try to debug application, it doesn't start application probably because debugger programmed application without the right...
