I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
HI ALL,
v2.8.0, nrf54l15, using the "periphral_uart" demo without any modifications
I downloaded nrf52840 using v2.8.0 and it runs normally, but nrf54l15 has issues. ...
Hi,
I am trying to get the sample projects working with the dongle, I am having difficulty with compiling the bluetooth examples using the provided instructions:
https...
We are running an NRF52840 on our custom board and getting around 450 uA while is BLE Advertising with a period of about 1 second.
If we disable BLE then our current consumption...
Hello I have a custom board with LR1110 Lora radio I'm getting errors that driver is not supported when I define the spi1 for it
lora0: lora @ 0 {
compatible = "semtech...
I am looking for a solution where I can set custom and configurable root Kconfig file via Cmake cache variable, which can be specified through the west build command.
Steps...
Hi,
1.How to determine whether the nRF54L15 LFRC has been calibrated? 2. What logs can show the calibration completion event? 3. Or, apart from logs, what other methods...
Context:
VS Code
NCS 2.9
nRF54l15 custom board
Mac OS Sequoia15.5
peripheral_lbs sample project
Goal:
The goal of this project is to create a bluetooth beacon...
We are working on a prototype of nrf9151 with various sensors and nrf54L15. Our schematics designer says U13 (TCK106AG) may not be needed. Please let us know its use. regards...
Hello,
I am new to nRF development. I am going through the nRF Connect SDK Fundamentals course.
I wanted to configure a GPIO on the nRF52833 DK board as an output and...
Hi，the Nordic team
I use the SED device by system on mode.I found that my static average power consumption increased by more than 20 ua after I defined an IO port to use...
Hello, I'm running an example of channel sounding using nRF54L15.
The build is fine, but the following error occurs during flash.
Python is using 3.12.4 version. As you...
Dear Team,
I have recently acquired NRF54L15 Development Board for evaluation and from Day 1 experiencing issues with BLE.
I am running simple Zephyr-based BLE Peripheral...
Hello everyone,
I am a EE student and this problem came up during my first big project in zephyr. I'm trying to connect a pwm peripheral (pwm1) to the timer 2 hardware timer...
Hello everyone,
I have an nRF5340 microcontroller (NORA B106 module), and I want to connect a square wave signal to one of its pins to read its frequency or count the number...
