We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
HI, I am new to embedded system and just start to learn NRF52 DK. currently I want to configure a pin of nrf52 as interrupt. so i created new GPIOTE_Handler function . however...
hi, i am getting a lot of help in here, thanks a lot
i'm using SDK 6.0.0 for my project. and i want to use timer as a counter like as the title.
then, i fount the app_timer_cnt_get...
hello,
I am using S130 softdevice. While I am trying to connect with MCP I am getting one error with error code :0x08. and MCP is showing a message like "Lost connection...
Hi,
I have a battery powered device which goes to system off mode when it is not used. I want to do some stuff when the battery is inserted the very first time after production...
My application uses the Softdevice, app_timer and app_pwm.
So all timers are in use, but I have to measure two more pwm signals on two input pins.
(Those come from HC-SR04...
Hi,
I'm resetting the chip externally using the reset pin to not be in debug mode. I'm running the system off example here modified to not use buttons.
I have the J...
Hi,
I am looking for some assistance to choose the best way using the nrf52832 processor in a correct way.
The main task is to generate a 1KHz PWM Signal with changeable...
Hello,
I am using nrf51822 ceaa package.
What would happen if dec1 pin is not connected to a capacitor?
According to the datasheet, it is for power decoupling and...
I'm developing py script for automation testing of nRF devices.
My script is based Nordic's scripts Master Control Panel\3.7.1.8567\lib\dfu...
So, during testing my script...
Hello,
I have some devices based on NRF51822 using ESB lib and developed with Nrf51 SDK v10 (no softdevice). Since Nrf5 SDK v11 is released, the new device will be developed...
Hi,
I am curious about how the connection is keep while using the 32.768K in BLE link layer in power saving mode.
I know that the connection interval is based on multiple...
Hi,
I have two BLE centrals and one BLE peripheral. Both centrals are in range of the peripheral and both want to connect to the peripheral at exactly same time. What central...
Hello ,
We are working to an OEM Security System project that is using BLE.
The system contains at least 2 modules that communicate using the BLE technology.
One of...
I am trying to run the example ble_app_hrs on the nRF51 dk PCA10028. I target and build the file, and I believe it makes it onto the device, as the old program on the device...
