When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
i am using nrf51822 to develop our product. I'll try to describe more details to make you understand more clearly.
STEPS:
While testing my project, I had...
Is it compulsory to have same Baudrate on central & Preipheral side when using the NUS..?
I'm using Central @ 115200 & Peripheral @ 9600 [No flow control on either].
...
Hi,
I've written an app on the nrf51822 (rev2), with S110 (v7.3.0) and SDK v6.1.0. I've written a custom non-blocking UART driver. I'm running into an issue where the UART...
Hi,
Using the nRF5 11.0.0 release SDK, I'm trying to set up one task to transmit to and one task to receive data from the UART. Nothing special.
The configuration block...
Hi,
The xQueueReceive function in FreeRTOS seems to be broken, when a non-zero timeout is specified.
Example, I'm trying to create and ordered output mechanism for the...
Hello there,
I managed successfuly to build the 'ble_app_hrs' of SDK10 on my NRF51 on GCC MARS 2.0 using these two guides combined:
devzone.nordicsemi.com/.../
devzone...
When i use the nrf_drv_adc with NRF_ADC_DEFAULT_CONFIG i get the following compile errors:
rf_drv_adc.h:127:27: error: 'ADC_CONFIG_IRQ_PRIORITY' undeclared here (not in...
I am developing a real-time system which triggers an interrupt every few milliseconds. That data is collected in the interrupt. When a memory buffer is full, the data is then...
Hi,
i am trying to start a RTC0 on nrf52 DK with SoftDevice (s132) enabled with project based on "ble_app_template". The problem is that a sd_softdevice_enable() (called...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have setup a development environment using Eclipse and GCC. This setup works nicely. Thanks!
devzone.nordicsemi.com/.../
I noticed different examples in...
Hello,
We are currently designing the hardware for a production run of our product using the nrf52832 chip and would still like to have debugging capabilities with breakpoints...
I have been learning GCC+ Make work flow to build and debug nRF51822 S110-only applications based on the examples from NRF51 SDK v10.0.0. I started with ble_app_beacon example...
I tried to work application.
But firmware stops at advertising_init(). When I exchange advertising_init() and services_init(), firmware does not stop.
why ?
S110 v8.0...
Hello,
My device is nRF51822 SD110 8.0.0.
The problem occured after firmware update in bootloader (own, not SDK) with readback protection enabled.
So bootloader connects...
