Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am using the nRF5_SDK_11.0.0.
I want to state of the system off sleep after entering system on sleep.
For example, from the state of system on sleep, it becomes system...
Trying to compile the HRS example using SDK12 using Eclipse. Getting a lot of undefined reference errors under the peer_manager folder for pdb_ and pm_functions such as these...
We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hi everyone,
I have a nrf52-DK, I made samples with the saadc unit and i noticed there are unexplained peaks.
I connected the MIC's output (its VDD is from the board)...
Hi I bought quite a few of these on boards on e-bay and have worked a lot with them.
One thing that is confusing me is the variation in the number of retries, even when...
Hi,
I have tested a sample code which sends some data through BLE in nRF52 development kit(PCA10400). The code is attached below.
nRF5_SDK_11.0.0_MPU6050_Acc_X_Output...
I'm trying to compile the bootloader_secure example for the 10040 dev board using make, and it appears the makefile was not updated correctly with the changes made to the...
Segger RTT viewer is a great debugging tool. But every time when I download new firmware into my board I have to close the viewer and then open it after download is finished...
Hi guys,
in my application, I'm trying to do multiple fota, I succeed at the first time & after that I can jump again to the bootloader, but after that something is going...
I used nRF51822 IC and SDK11 with softdevice S130. I found a problem that our product cannot work. I dumped the hex code of 2sets from 0x00000000 to 0x0003ffff. One can work...
Hi,
I am using the nRF51822 module. I am facing problem to send multiple data formats packets over nrf module. I am using nrf SDK 11 version.
I am attaching my code with...
I want to start developing a Bluetooth device with the NRF52 DK. For debugging and sniffing purposes to see what is going over the air, use the NRF51 dongle, get a NRF51 DK...
In the nRF52 specification, I cannot find figures for the interrupt latency for event on GPIO pins in different power mode OFF, ON (constant latency, Low Power).
Can you...
Hi. I need to use direct advertising option in my application to minimize the time needed to establish the connection.
Firstly, I set up the connection during "normal" fast...
