Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
just passed Cellular IoT Fundamentals while I was waiting for my nrf9151dk to be delivered... Now that I have the DK I can't get the dk to be provisioned...
I couldn't get...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hi all,
I am a beginner with nRF24LE1, when I want to code some examples using GPIOs, I find that it's difficult to understand the PxCON register function. Whether I configure...
I am using the usb port to download an example project to the NRF development kit board, with Keil4. Somehow it keep telling that "No jlink device found", in Keil, the project...
I'm designing my own pcb with a IMU and nRF51422 but i confused,
What's the best choice, LDO, DC-DC or external regulator configuration if I'll use a cell coin?
Someone...
Hi,
We bought new some new nrf51822 beacon boards to get latest revision HW. Then upgraded Keil uVision to latest 5.13 and installed SDK 7.2. However I can't get anything...
I would like to use a network of nine nRF24L01+ nodes {n0, n1, ... n8} in following topology:
n0 has bi-directional links with n1, n2, n3 and n4;
n1 receives from...
Hello,
i'm using nrf51422 with gazell protocol.
Here is my interrupt on success code
void nrf_gzll_device_tx_success(uint32_t pipe, nrf_gzll_device_tx_info_t tx_info...
Hi,
I'm using two STM32F407 discovery kits with one nrf24L01+ module attached to each kit.
Here is my common init code (common for both Tx and Rx):
RF_Init(); /*...
hi:
On ios8 system, sometimes after iphone switch Bluetooth, ancs does not work,
because apple_notification_setup() is not work, but try calling apple_notification_setup...
Hi Nordic DevZone User,
i want to ask if there is a limit of devices which can be found within one scan process?
And how many connections can one master have at the...
We have two nRF51822 chips ("A" and "B") connected via GPIO pins on our board, communicating via UART using the app_uart SDK module (in APP_UART_FLOW_CONTROL_ENABLED mode...
Hi,
I found this (PCA63506) Nordic Board, which I suppose is some kind of audio interface for the Smart Remote 2. However, I am unable to find more information on this...
Q: Is qualification process simplified by some sort of NRF81522+ S110 stack BLE pre-qualification (up to GATT level, what BT SIG ask for BLE devices)?
We use NRF81522 with...
After SD initialization and turning on advertising i have to send large amount of data via SPI continuously. SPI driver code initializes SPI module after SD init and advertising...
Hi,
I have an ISP130301C chip based on the nRF51822 chip.
I'm using the jLink Segger EDU to flash the chip without any problems.
But it seems like nothing is running...
Hi,
I just took a look to nRFgo to see how it generates vendor specific UUID's. It looks if they are generated completely random including the version number. According...
