Hi there,
My nRF5340 application requires the use of SD card with DMA and BLE transmission. Howerver, as soon as I turn on the device, I get the following errors:
A...
I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
Is it possible to use nRF51822 Development Kit without nRFgo Starter Kit? What I need - is to be able to connect couple of LEDs and buttons, can this be achieved without buying...
Hello,
after successfully calling sd_softdevice_enable(), I call ble_cscs_init() and that function returns with error code 7, which means NRF_ERROR_INVALID_PARAM. I've tracked...
Hi,
After doing an sd_nvic_SystemReset(), the bootloader does start advertising, but for some reason the android app nRF Master Control cannot connect to it.
If I connect...
Hi everybody,
I'm currently writing an Android application allowing me to communicate with a NRF51422.
I've created on the Nordic chip one proprietary service with 2...
please help to confirm the ESD grade of nordic SOC. i can't find all the parameters(HBM, CDM,MM) in the datasheet, only HBM in 24LE1, and only HBM&CDM in nRF51822.
I'm trying the ble_app_hrs example on a custom nRF51822 board with s110 6.0.0 softdevice.
Debugging in Keil, the firmware runs fine up to ble_stack_init(). Within ble_stack_init...
Hi All!
In all exsamples in function "ble_evt_dispatch" we have different order to call sub functions.
Most functions to call is:
dm_ble_evt_handler (device manager...
I'm testing a data collecting program which samples data every 2s and reports it through UART ( printf("data=%d\r\n", data) ) on a PCA10001 board. I found this program may...
Hello,
Got a question about nRF51422 and S310 stack. I am trying to understand how the radio is being handled and how the softdevice handles events in a specific case....
I tried communication between PC and my own board(nRF51822) PCA10000 usb dongle&MCP, I found that the first time I send n(where n is any decimal number) bytes data(s) from...
Dear Nordic guy,I'm developing with nrf51822 (6.0 stack binary and 5.0 SDK).
I recently updated the code and stack binary(6.0 stack binary and 5.0 SDK).
My function is not...
static conn_mw_handler_t conn_mw_handler_get (uint8_t opcode)
Inside the function,
for (i = 0; i <conn_mw_item_len; i ++)
{
if (opcode == conn_mw_item [i] .opcode...
