I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello! I need to perform some radio tests on a board that contains an nRF52 SoC. The nRF5 SDK provides two ways of performing such tests, either using DTM, as specified by...
Hello,
I am using pca10028 dk. I want to know how can I change the transmitting power of ble?
My application needs that user should be able to change the transmitting power...
Hello guys!
I got a board of nRF52 with a Jlink debugger on it through a serial port and I program it with nrf-connect-mesh-official-serial-gateway-fw.hex.
However, when...
I am programming a Ble Nano device using Nordic SDK. So far I have been using examples from the ble_peripheral and ble_central directories. Now I want to run an example that...
Hi,
I used the nrf51822 as the spi master,it could send out the data, but it didn't receive the slave data.Did I miss somthing?
static volatile bool m_transfer_completed...
I'm working the the NRf52 dev board and SDK12.2. I was able to successfully load the standard DFU example and then use the NRF Toolbox on an android to load the example HR...
Hi.
I'm getting an nRF Dongle (PCA10031) set up on a Windows machine to be the BLE central that we'll use for our production line testing. To that end, I've built the pc...
The pc-ble-driver project uses CMake to generate Solution and Project files for the Windows build of the project. CMake uses absolute paths in these generated files. I can...
Working with nRF52832 and SD132-v2.0.1
Using Timer 1 at 1MHz (pre-scale 4) and 32bit bitmode CC to trigger events at a pretty wide range (from us to minutes).
I'm getting...
I am calling certain services and I can see this output on my UART listener:
0.000013 : UART Start!
0.385355 : BLE Stack Initialized
0.385581 : Peer Manager Initialized...
What would be the best value for UART buffer?
When I put it as 512 it gets crashes, below you can see the putty output
0.000013 : UART Start!
0.415937 : Handle list for...
I want to use app sched feature, so as example does, I call:
static void scheduler_init(void)
{
APP_SCHED_INIT(SCHED_MAX_EVENT_DATA_SIZE, SCHED_QUEUE_SIZE);
}
since...
Hi Team,
I need to make an application that we receive a data from a chip through UART and need to send the data to Console through another UART. Is it possible to make...
Hello,
My setup:
PCA10040 DK,
12.2 SDK
I copied the "BLE_APP_UART" example into my project folder and want to "upgrade" it with the TWI.
So I copied parts of the "twi_scanner...
