Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hello,
I was trying to build Clapp oscillator with a JFET J310 (FYI: link text )as it is shown in the figure.
Capacitor C is variable and goes from 20 pF to 285 pF...
Hello
Please tell me about sd_ble_gatts_value_get ().
Please tell me about sd_ble_gatts_value_set ().
For these two cases, it is not used in the SDK, but is it old?
Please...
Hello together,
I' am working on a Bluetooth application and have a problem with the transmitting time of the Bluetooth.
In this Screenshot you can see the end of...
Hi,
I want to connect an ADXL362 low-power accelerometer to a nRF51DK via SPI for a BLE application. However, I'm still quite unfamiliar with Nordic Semi's BLE offering...
In SDK12.2 init timer user APP_TIMER_APPSH_INIT(APP_TIMER_PRESCALER, APP_TIMER_OP_QUEUE_SIZE, true);
but when I want to use more timer,how can i add the number?
Dear Nordic,
I am having some apparent delays in the time that passes from the pressing of a button, and the execution of the ISR that this button triggers. I am using...
Hi, Nordic
I checked DFU operation, found DFU work in bootload mode.
I want to know below operation is OK or not. Plz help me check:
download DFU bootloader
download...
Hi, I use the PCA10040 v1.1.
This is an example of a PCB stack-up.
My questions are,
In the case of PCA10040, which is 4 layered, what are the values of...
Hi,
I am writing a firmware for one of my custom boards which use GPIOTE to detect interrupt for 3 GPIOs inputs (P0.03, P0.06 and P0.09, both with internal pull-ups) and...
Hello,
I'm trying to write my ADC samples over spi on a sd card (Using SAADC like in the sdk 12 example with PPI and using fatfs like in the example in the sdk).
I open...
I have been using the pc-ble-driver Python bindings to implement a peripheral. I have extended BLEDriver to support sd_ble_gatts_* the functions. I now have a working peripheral...
Hi All,
I am struggling with this question from many days. Does the SPI transmit or receive operation in SPI master code uses DMA? While using SAADC DMA I have specified...
I'm using an app timer to blink an LED while in the bootloader.
Initially I was configuring an app timer when the bootloader started up and never stopped it, assuming the...
After failing in replacing a Cortex M4 for a NRF52832 I'm studying the possibility of using a NRF51822 as a BLE controller, used by my Cortex M4 MCU.
As I saw there is...
Hello
Please tell me about sd_ble_gatts_value_get ().
Before execution, handle is 0x11, but after execution it will be 0x00.
Is this an abnormal thing?