hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I would like to know, whether it is possible to use a TCXO with single output as a LFCLK source, i.e. connecting the TCXO output only to XL1, instead of connecting an...
Hello everyone, I encounter a question. I follow below link to solve the issue.
https://devzone.nordicsemi.com/question/104118/adding-pwm-to-ble_template/
I've set the...
We are currently porting our proprietary stack from the nRF51 to the nRF52.
To save on BOM we are using an external 20ppm 32Mhz crystal to synthesize a 32Khz clock (power...
Hello,
I have develop an android application which connects to BLE device and perform read and write operation, so for this i was using Android-nRF-UART .
But my application...
In the release notes for the IOT SDK (which as the MQTT examples) it says: "Once BLE link is disconnected, lwIP example applications no longer get a global prefix. The only...
Hello all,
I am new to ARM architecture with some prior experience in Arduino based application development and some FPGA experience. I have a few queries:
Should...
I'm developing a project based on the Nordik UART Service and I wouldn't use pairing as in the example.
However I have some problem when a central device is already connected...
We're targetting the nRF51822 and use the pc-ble-driver (via connectivity_1.1.0_115k2_with_s130_2.0.1 )
Currently I'm using the dev board and the virtual COM port connection...
Hello,
I am trying to move from ARM Compiler v5.06 to v6.4, but I encounter an error, which I cannot handle.
The project builds fine with v5.06. When changing to v6...
Hi;
I am trying to secure DFU OTA. For that, i am using SDK12.2.0 and done with example file.
Now how to generate this .dat file itself.
Also explain each parameter...
I've been using a HC-05 (bluetooth v2.0) to communicate between my Unity-Android app and my Arduino microcontroller. It's working fine, however, if my prototype continues...
Dear all,
I have been working with a nRF51422 device for about two weeks, and everything went good.
This morning, out of nothing, i got this error in IAR: Warning: Stack...
Hi,
I have disabled the reset functionality of SW5 on nrf52840 PDK by giving the following command
" ./nrfjprog --recover -f" as it is mentioned in PDK document.
Now...
