I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hi,
I asked the same question but it was a long time ago and still I don't know how to solve this issue. I got a reply but It wasn't help so now I'm writing again with...
Hi
I am new to the nRF kit and C, but I have a project where I shall use the nrf51822 as master and MCP3201 ADC as slave. The nRF is only going to read values that i give...
Hey! I've been working on triggering DFU from within my application. It's obvious that the bootloader in the new SDK has been written to support this but I had some problems...
Hi,
I need the softdevice to be able to receive and send data on it's own without necessarily connecting to iPhone or anything. So:
device1 (nrf51822 receive and send...
nrf8002-based loss prevention solutions are being developed.
our often experience intermittent connection to iOS 7.
Disconnection from the moment after a successful...
There seems to be a lot of questions recently that are re-hashes of previous discussions.
Many discussion forums post a sticky etiquette thread. Can we maybe have something...
The nRF51822 only has one UART and my app needed two. One for a GPS receiver and one for a simple terminal command line interface. The UART RX is interrupt driven, but TX...
Hello,
We are developing using the S110 and having major trouble re-establishing Bluetooth connections to our device. The reason we need to reconnect to our device is to...
Hi all,
I found something different between SD6.0 and SD7.0:
1.KB bonds with iPad successfully;
2.Click OFF the bluetooth button in iPad setting, then KB goes into...
I'm trying to get the ble_app_hsr example working with BLE_DFU_APP_SUPPORT enabled. I have included:
ble_dfu.c
dfu_app_handler.c
bootloader_util_arm.c
But when I build...
I'm using a nRF51422 with the s310 stack. I copied code for adding a custom service that was working with a s110 stack, and tried to add a service to the BLE in the s310....
Hi,
We are a couple of students from Norway trying to get RSSI from an active RFID system we got from ebay.
We have now connected the tranceiver module to our PC running...
Hai,
I am using nRF51822 development kit. I want to test the demo app for S130 soft device using this. But i could find that the demo app is for the evaluation kit. I am...
Hello,
I'm learning how to use s110 and the debugger. I am porting the hids_keyboard app from the PCA10001 to the PCA10003 (nrf51822 -> nrf51422).
As described in this...
I am installing nRFTools_6_1_0 and I get this error during the instalation.
I am trying to connect via USB the PCA10001, but my windows 7 says that the driver is missing...
