Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi team,
I downloaded nRfgo studio , keil compiler,and sdk 12.1 version and i able flash ble_beacon example on nrf51 dongle.I have www.nordicsemi.com/.../nRF51822-Development...
The work I finally have to complete is,
It is to port nRF 51822 project to nRF 52832.
There are two kinds of projects, KEIL and mBed.
Could you tell me the best way to...
I would like to know the files contained in nRF5x_MDK_8_9_0_IAR.msi
as well as other files needed for a minimal application.
I would like to know exactly which are those...
Hello iam using softdevice 110 and SDK 10.0.0, i want to know the way to avoid bonding of device more then once, or deleting the bonding information from persistent memory...
I need to change the flag of the scanrsp. I use the advertising_init() and i try to do like this:
scanrsp.flags = FLAG;
but the function ble_advdata_set(&advdata,&scanrsp...
Hi,
I'm tring to generate private key of dfu, but it didn't work fine.The following is my steps.Did I miss something?
C:\Users\Administrator>cd C:\Program Files\Nordic...
I'm trying to tune a chip antenna for nrf52832. I am not an RF engineer but have figured out how to get the basic VNA measurements done.
I've been fighting with finding caps...
Are there any dirty hacks to pass a little data, like 1 bit even, during pairing?
I need my central to tell the peripheral orientation, left/right, as early as possible....
I am using an nRF52832 PCA10040 board, using s132_nrf52_2.0.0_softdevice.hex, and have AIN0 connected to a potentiometer similar to this . The power input pin is connected...
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hello,
So — in just trying to get the blink example working, I've come across all kinds of toolchain weirdness. I'm using CrossWorks, because it's on OSX and it's way cheaper...
Hi all
Is possible from softdevice or from program application edit the GAP service? I know this service is mandatory but what about edit the structure which is shown on...
Please give me a professor.
In the nRF 52832 sample project, there is an NRF_LOG_INFO function, is this the ability to output a debug string to the UART?
If so, how can...
I have custom service, where I have declared 2 handles inside BLE Service structure, one for button action and the other for custom battery ADC measurement, each identified...
