This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Recently I open the sdk of the nrf51422,there are some functions that indicate that they are come from the document call 'ant_interface.h'.But when I try to go to the definition...
I'm ending up in the HardFault_Handler() on calling sd_app_evt_wait() within a function that reads from the UART. What might cause that? Stack screenshot attached.
I have...
I'm using nRF51822 for development. and I want to use ADC to measure the electricity of battery, but I don't know the discharge characteristic, i couldn't get that on internet...
#define IO_CHERRY8x16_ROW_PORT 0x13E02040UL
#define IO_CHERRY8x16_COLUMN_PORT 0x60031FBFUL
Why this number be defined like this ? What are this two things use for?
...
Hi,
I'm trying to compile the bootloader example using GCC instead of Keil compiler.
To do so, I copied the bootloader example and started editing the file bootloader_util_arm...
Hi, I am working on my new project. My goal is a sensor network. I have to create four service, one or two basic service like htm and battery service and other with contains...
Referring to the PCA10001 schematic, there is a solder bridge SB1, which connects AVDD with VCC_nRF.
Can you please explain in which cases is it needed?
Thank you
...
Hi all,
I test the DFU as follow:
erase chip, program "s110_nrf51822_5.2.1_softdevice.hex"
program "bootloader" by using nrfjprog.exe
"DfuTarg" can be found...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
I'm trying to build the bootloader for gcc/Eclipse.
I used the manual setup approach described here.
However, I can not fit in the allocated space, because...
SDK version: 5.1.0
S110 version: 6.0.0
chip: nRF51822
I am experimenting a generic Data transfer hid device, the report map is as follows:
0x05, 0x0C, // Usage...
Hello Nordic team,
I am working on a BLE RedBearLab shield (nrf8001) mounted on an Arduino board.
Consider that a connection is correctly made from a Master app to my...
I've been running various code on a 51822 that has used PPI, timers, events, GPIO pin config and so on. Supposing I've lost track of what state the retained registers on the...
Hi,
I am new to ANT programming, and was following the userguide's steps to set up my nRF51422 evaluation kit (pca10003 board). I can compile and upload the blinky example...
