I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
I really need your help regarding a problem. I developed my own pcb with nrf52 and verified it with your hw engineer. I just finished soldering and hooked it up with your...
Hi,
Is there any ready made app of NRF52 and NRF51 ( beacons), where beacons are communicating with the NRF52 and based on some nordic app for PC we can view that how many...
I have created a BLE peripheral device using nrf51822. I have used sdk12.0.0 with soft device 130 and I am using NRF connect mobile app to test my device.
When I connect...
Can I create Characteristic with Notification only, no Read, no Write
I can remove the //char_md.char_props.write = 1;
and only the Read and Notify Properties show up...
Hi,
I am totally new to NRF52832 chip and I want to use ANT+ in my sensor networks related project. I am using keil compiler and S332 softdevice (I am also using BLE therefore...
Hi,
I am working for the first time with NRF52832 flash data write. I have (ANT + BLE) application and and I basically want to save the data in ROM in order to keep it saved...
Designing a custom pcb, we have a few questions, and maybe you could help a little bit.
On this Nordic design ,before proceeding to layouts :
Can I skip pins 45/46...
So im trying to create a generic library to test any Bluetooth device. So far i can connect to the device but since i dont know what are the services and UUID available im...
Tried Flasher Portable Stand-Alone Mode with J-Flash 6.14 as following:
Create .jflash Project for nRF51822-QFAA
Open Data .Hex File
From J-Flash, select Target...
Hi,
This is obviously not the first question about this, but I still haven't found the answer I need here...
I would like to make a kind of serial to BLE gateway on...
Hello Nordic Community.
I'm having issues trying to control a simple RGB LED circuit with the NRF52. I have set up 2 timers and PWM instances Red and Green on PWM1 and...
I am performing automated testing on my device using an xml file that I have written. My xml contains a disconnect command. I observed that NRF connect reconnects to my device...
Hello,
After looking for pin mapping for TRACECLK and TRACEDATA[*] for nrf52840 I've seen 3 different mappings:
P0.07, P1.00, P0.11, P0.12, P1.09 in infocenter.nordicsemi...
Hi
I need to send as much data as it is possible in the advertisrment payload. Whem weset the devicename there are other fields that are automatically added to the payload...
