After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hello,
I'm trying to set my device on DFU mode by an android mobile application without success.
I'm working with nrf51822, sdk10, softdevice 8.0.
I subcribe to the...
Hi.
I'm using PCA10028, SDK12.2.0, S130 as central.
As I know "sd_ble_gap_tx_power_set" function let me set Advertising Tx power.
How can I set Tx power if i want to...
Hello,
I am going my project with NRG51822 in SDK 11. I build a android app that can connect to my device and access vendor specific service.
My device dedicates one...
Hi, All,
I'm testing multi-connection central function.
And I am struggled in getting relation of address.
AFSK, there are several types of address in BLE.
I found...
Hi.
I'm using nRF51822AC, SDK12.2.0, S130 as central.
After "sd_ble_gap_connect" function, how can I stop this function before connection?
I hope your reply.
Hello,
Is there a way to temporarily disable bonding and just allow any connection? I want to generally use bonding, but there are certain corner cases where I need to...
Hello,
I want to use the FDS libraries in order to store some data into nrf52's flash in my application and I have a bootloader to allow secure dfu by ble.
I manage...
I'm struggling with current consumption. I need my device to completely sleep and leave only the RTC on when the ext power is off (run on battery). After making sure my RTC...
Hy everyone!
I'm trying to write a non-volatile memory position of a device via I2C (twi), the device, a flash memory is the slave.
In my application, I have configure...
Hi I am using the SDK 12 and I am doing some test using the experimiental_app_ble_blinky central and peripheral parts.
I see in this example it use boolean values to indicate...
Hi,
I am using the experimetal app_ble_blinky on both sides peripheral and central.
I edited the peripheral characteristic sizes to 4 and I am able to send notification...
I am trying to modify the default mbed bootloader to include support for watchdog.
I'm running with nRF51822AC (NRF51DK).
My program is written with mbed classic (uses S130v1...
Hello
I got this nordic nrf24l01+ module and trying to interface with pic18f25k22. this is my code. tried lot but unable to communicate (receive any data). I'm able to...
Hi!
Does someone tested the range of newer NFR24L01+ module with external SMA Antenna?
Any result?
As we are looking for a module with a range of ~1000m line of sight...
Hello,
I only recently discovered Nordic Semi and I'm looking through the various products. I'm wondering what Soc offers the lowest link latency for audio, seems like 2...
