Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hi,everyone.
because of careless,i enabled pin reset in debug mode by set bit 0 in RESET register in my software,and i downloaded the hex file to a 51822.now,because of resetting...
Hi all
According nRF51822 Product Specification , GPIO pin can config to SPI interface. Means if I set a specific GOP pin range to SPI and connect these pins with...
I am successfully sending data from the PCA10001 Evaluation Kit to the Master Control Panel. But I cannot find any information about initiating and sending data from the MCP...
Hi,
Here i am attaching my text file. in my case timer api is working
but button event handler is not calling.
Kindly tell me , what is my fault.
Regards
Balaji...
I want to store a block of data in nRF51x22. I tried the following:
void HalStoreNVMBlock(uint32_t size, uint8_t* pBuf)
{
nrf_nvmc_page_erase(NRF_UICR_BASE);
nrf_nvmc_write_bytes...
I'm using the TWI module. Where can I set whether the DSA SCL pins have the internal pull-up enabled or disabled? I can't even find where to see if they are enabled at all...
Hi guys,
I am having a breakout board made and would like to know what are the programmers out there which I can buy which will help me program the board. The J-Link is...
Hi,
I'm designing a custom board equipped with nrf51822 and is not clear for me how the flashing part works; I bought nrf6700 and pca10005 as reference design and now i need...
I am coming across a strange issue with a nRF24L01P running enhanced shockburst. I have 1 PRX and a few PTXs communicating in a star network. The type of PTX determines which...
Here i am attaching text file in which my application not able to call interrupt handler.
Kindly tell me what will be issue.
Regards
Balaji
rtc1_app_timer.txt
I'm trying to figure where the BLE bottlenecks are to figure if I should use BLE or maybe Gazell for my product. I've just started to use the BLE stack, so I guess that there...
hi,
i am working with the nRF51822 development kit and trying to load the sample programs given by the nordic guys, the samples without using BLE is working properly but...
Hello,
While debugging, I found that if there was an active BLE connection, the chip would reset when I switch to single step mode, is there a way to avoid this from happening...
From the log:
[23:41:27.2] EnableServices({11:2,16:2,22:2,28:1,})
I suggest that you use hex for the handles - this is what you use upon inspection and other log statements...
