On future revisions of the nRF52840 Dongle, and on future development hardware of a similar form factor, I'd recommend putting a debug connector that's compatible with the...
Hello,
I am trying to measure nRF9151 current using Power Profiler Kit II, running Cellular UDP project on EVK and following the steps in:
https://docs.nordicsemi.com...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
We are developing a very low power product. In some cases like not getting registered, PSM not being available, ... we want to drop the connection and go to a sleep state...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
Hi
I am trying to use nrf51822 as both peripheral and central device for my application.
nrf51822 as peripheral checked satisfactorily with a smart phone as central device...
Hello,
I use EV-board PCA10040 and run I2C demo on path nRF5_SDK_11.0.0_89a8197\examples\peripheral\twi_sensor\pca10040. I measured the current over 5.7mA .if modifing the...
Hi.
I've got little problem with the uart connection to one peripheral. It's a normal 2-line connection without HW flow control. I'm using app_uart_fifo. HW is nRF52 with...
Hello,
i have a problem with the PCA10040. I try to set up a ANT Transmit Channel.
If "ant_channel_init" is called from main everything works fine.
But if it's called...
Hello,
I am developing in NRF52 with SDK v11. Initially I want to use CMSIS DSP library for statistic and FFT functions. However, I read that CMSIS Pack is not supported...
Hi,
I wrote a functional firmware which has been tested and valited on a nrf51822 QFAA, but unfortunately I need more RAM to fit the requirements of my application so I...
In the Android version of the Master Control Panel I'm sure that earlier versions of it hid the 'Connect' button for non-connectable devices. It seems they all have it now...
I'm starting to get things moved over to Peer Manager in SDK11 and when I call pm_conn_secure I get NRF_ERROR_NO_MEM. When reading the manual it states that this error means...
I'm using sdk10, I tried the bonding feature using device_manager and it's working. but then when I perform DFU, the bonding information is erased. I can't modify the bootlader...
There's a note in the migration guide which says .. very ominously ...
Applications must not modify the SEVONPEND flag in the SCR register when running in priority level...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Dear Sir
In nRF51822 xxAA (Ram is 16kB),
softdevice(s120) is using RAM (address: 0x2000_0000 ~ RAM_R1_BASE).
I think that SoftdDevice region is used, after sd_softdevice_enable...
Hello,
It just a diode drop away from 3.9 to 4.2, and 20% typical of a Lipo discharge, just wondering whether the IC design and process is really that tight. The nRF52...
I recently tried to add security features (encryption, no MITM) to my application, and I am using nRF Sniffer to verify. nRF Master Control Panel gives me the request for...
