Hi everyone,
I'm developing a Matter device on the nRF54L15 platform using NCS 2.9.0. When commissioning the device via HomePod and iPhone, the device unexpectedly reboots...
Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK using libraries from Nordic (nrfx_rtc.h, nrfx_clock.h and hal/nrf_rtc.h). I am not...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Previously I implemented a DFU bootloader. It works fine on s120 softdevice.
But after I ported it to s110 v7.0 softdevice, it can not work. After investigation, I found...
Hi,
i just followed the steps for migrating to peer_manager - as lines out in the tutorial.
However i will never ever get a callback to pm_evt_handler.
I am trying...
Hi,
I am facing some issues on the Android part of the BLE.
Firstly it takes around 20 seconds for the android phone in scanning mode to find the nordic board. This...
I encountered the following error while adding device manager to ble_uart_app in SDK_11 s130 using the hardware nrf51-DK. I'm using Keil compiler.
._build\nrf51422_xxac_s130...
While using the device manager, I encountered this line;
#define SEC_PARAM_MITM 1 /**< Man In The Middle protection not required. */
Since security is important, is...
Hello!
I'm trying to test several types of ANT communication like broadcast, background scanning, etc.
And When I check ANT broadcast rx example, I realized that some...
Hi Support Team,
i want to know the voltage range of AVDD(internal DC/DC output) of NRF51822 when DC/DC enabled, please help to check.
i don't find this information in PS...
I use nrf51822xxac, sdk 9.0.0, sd130. When I connect to some beacon as a central I no longer receive BLE_GAP_EVT_ADV_REPORT and I am not able to receive advertising packets...
Hello,
We do not want our beacon on at all times. I suppose our need below has been asked before.
Is there a sample snippit of code, or a document on ble_app_beacon...
hi:
i want to create timer in my code, i create timer and start the timer ,but the timer do not work,i found timer number can not exceed four,detailed information in the...
I found a bug in the FreeRTOS port provided by Nordic for the nRF52832 in SDK v11.0.0. This bug only applies if configASSERT_DEFINED is equal to 1, as the affected code is...
Hi,
We are assessing the pros and cons to port our software to work on S130. We are currently using S110 (Peripheral) and S120 (Central) on nRF51822 rev.3.
Based on the...
I am running ble_app_uart sample code on nRF-dk using SoftDevice n130. It is working fine.
Currently, when nRF UART app connects to ble_app_uart, user does not need to...
I have hard time in start a twi in nrf52832 with SDK11.0, I can't initial twi ,whatever i do ,when i build is still an error ,here is my code:
static const nrf_drv_twi_t...
Hello. Nowadays I'm trying to upload the softdevice for the RTOS based on the freertos.
As you know, determinism is very important for the realtime.
I want to know the...
