board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
I have an application programed on the nRF 52DK (PCA10040). Its a UART communication to a distance sensor. The Problem is, that I cant send anything from the uC to the Sensor...
Hello,
I just run in following issue. I try to configure an UART to send some bytes. To check the configuration, I just let the program loop, after the sending. Attached...
Hi all! I have a smart beacon kit rev 1, with s110 on it (the latest firmware available). I am using the RTC with the 32 kHz crystal (50ppm) to trigger an ADC conversion every...
After releasing reset to the nRF51, its UART is responding with
RX: A4 1 6F 1 CB
Further requests for things like capabilities, etc go ignored, and opening a working...
hi all,
i cant able to find the version 11 softdevice hex file. can you please send the link.
and can i use the version 8 softdevice for version 11?
-Thanks in adv...
In the migration guide, I can read: "Clearing an interrupt event may not take effect immediately."
And an example of required code is given as:
NRF_TIMER0->EVENTS_COMPARE...
I'm creating a PC application using the ble windows driver by nordic, i cannot implement white list. I ported my code on the firmware & it works.
Is this a limitation of...
When i follow the Getting Started guide for the nRF52 DK at point 5 the led (led 1) does not start pulsating and I do not get contact with my phone. I tried to upload the...
I am trying to make communication between STM32F407ZET6 and NRF52832 chipsets using an SPI interface.
One is master and another is slave. If I take NRF chip as master,...
I am noticing a problem with pstorage_raw_clear when called in the DFU code. My problem is this: when attempting to update an application, if the application is too large...
HI, I have a remote control with nRF24L01. It was talking with Gen1(uses nRF24L01) product via ESB. Now, I am developing Gen2 product*using nRF51822xxaa) and I need to support...
Hi,
i'm doing my own bootloader and i want to use external flash to download image trough a spi. The bootloader project based on example from SDK11, now just an external...
Hello:
It appears (although I am not 100% certain) that there is a small delay (< 10 usecs) between EVENTS_END in the radio and MICSTATUS in the CCM. I believe I have read...
Hi,
I've got an application running on an nRF52, and it's calling sd_app_evt_wait() from the main loop - and it's staying in that function pretty much all the time.
...
I don't have a 32KHz crystal on my board (using the stock Rigado module) and power isn't an issue as the board is mains powered in operation, so I was intending on using the...
