Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
Hi all, i followed the tutorial " devzone.nordicsemi.com/.../" and did the challanges, however there is a detail i don't understand (totally newbie here!): the value of temperature...
Hi Nordic Community and Developers,
I'm designing a small Bluetooth module using nRF51822 to use it in my next projects and I need to use thinner substrate material (~0...
I have an application that we have ported to the nRF52 that used an EEPROM to manage configuration values. This application doesn't update these values often but when they...
Hi All, we have used Arduino modules based at 24L01+ in our application, now we are getting to apoint where we need to find one of theese or another one and do a redesign...
Hi, I'm searching platform for my project.
I will need to send packets from big quantity of transmitters (nRF24LE1) to one reciever (nRF24L01), it will something like voting...
Hi i am interfacing mma842with nrf51822. but i am not getting data. i have uploaded code. can you tell me what is problem. i don't know i am not getting who am i id try.r...
I've noticed that our custom board sometimes does not work (e.g. execute the code) when the VCC drops to about 0.3V- 0.5V and comes back on again to 3.3V.
For testing I...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
In SDK_v11.0.0-2.alpha, there is a project: examples\ble_peripheral\ble_app_hrs_freertos\pca10028\ble_app_hrs_freertos\s130_with_dfu_pca10028.
But I can't find DFU service...
to # einar thorsrud
Req: from the cap-sense board, different tap will be done by user (like 2 times tap, 3 three times tap etc). so the Bluetooth board (nrf52) will receive...
Hi
I am writing an app to utilise the new LESC feature using Diffie Hellman related pairing. I am testing the app against the Nordic provided ble_app_multirole_lesc. I...
with SDK 10 I found 2 SPI libraries, spi_w5_master and nrf_driv_spi . I hesitate between them.
what' the difference between them? and what should I use when I'm using app_timer...
I saw this tutorial:
nRF51 current consumption guide
It's specifically directed to the nRF51, but I guess the principles of Tuning Advertising parameters must be general...
i'm looking to use only one timer for two independent activities:
battery service (as in Nordic examples) and
a routine to detect a certain button press pattern ...
