Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
nrf5340DK
NCS 3.0.0
if I use sample zephyr/samples/boards/nordic/system_off it works fine and i can wake from sw0 press. but if i move the sys_poweroff() call int a...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
So long story short - I need to pair two devices: Arduino UNO with Seeed BLE Shield and Adafruit Feather 32u4 Bluefruit LE.
Now, Seeed shield is configured, and is able...
Hello, I am now having problems to get NRF51 DK to work. My computer is connected to board with USB. It can recognize it.
Now, here is what is something strange, when...
Not sure if this is the correct place to ask this question.
I can't seem to find the download location for the Master Control Panel PC application. It seems to only available...
Hello,
I am currently trying to generate a PWM signal on P0.00 and am not having success. If I drive P0.00 without PWM, everything works fine. Is there anything that would...
I have 2 nRF51 Development kits and a nRF51 dongle that I am using for proof of concepts. I am mainly using the nRF51 IoT SDK because we are looking at using IPv6 with 6LoWPAN...
I'm looking at log_uart_init in the nRF5_SDK_11.0.0-2.alpha and wondering if it would make more sense to allow the application writer to pass in a baud rate.
I'm trying to program a nrf51822 custom board using the SWD interface of the nrf51 DK. The board is using the low voltage configuration.
I'm not duplicating this question...
The IoT SDK Documentation page is getting Error 404 not Found.
Here is the error:
The requested URL /nRF51_IoT_SDK/doc/iot/html/index.html was not found on this server...
I know the softdevice region in the nrf51 is determined by the CLENR0 register.
But I read that the CLENR0 register is removed from the nrf52 and the MWU can be used to achieve...
Dear Sirs,
I buyed recently a Bluefruit LE Friend based on chip nrf51822. I triyed to get working with the ble-sniffer without success.
I don't have programming interfaces...
HI,all,
MERRY CHRISTMAS!!!!
i have an issue when i want to try the data transfer using timer
i have a idea about it , but i do not know how to achieve it.
-my project...
Hi,
Just got the nRF51822 Bluetooth Smart Beacon pca20006.
I would like to download the Firmware for it, but it requires a product key.
All I have is a set of stuff...
Hi ; Following my question how-to-flash-with-jlink-command-line which was successful, I can flash Soft Device and my app on my nRF51822 board (mac os x + gcc)
Now I would...
I am trying to set the transmit power of the NRF51822 (e.g., on the PCA10000, v.2.0.0, but the same happens on other nrf51-devices). I am not using any softdevice.
I use...
