Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
I want to use a timer to track time. Like having a variable that shows minutes/seconds/ms/etc.
But I don't know how to do with that.I want to use the rtc, but rtc1 had been...
Here are the commands I use to upload a program to the device:
JLinkExe -device nrf51422_xxac -if swd -speed 4000
loadbin filename.bin 0x18000
r
exit
It works...
Hi, I'm planning to made a custom PCB using nRF51822-QFAA or QFAC revision 3.
My developing environments are J-Link, IAR EWARM 7.1, SoftDevice 7.1, and SDK 7.2.
I kept...
Dear developers,
Currently, I'm developing a new application that uses Nordic Uart Service (NUS) over BLE.
Everything is working fine. However, I would like reset (delete...
Hi,
I've loaded SD 8.0.0 on the device, but when I try to load application via NRF Studio it always fails.
Im using SDK 10.
Memory settings in Keil:
IROM: 0x18000 0x28000...
I use s110 v8.00, now i need finish the dual bank ble DFU program.
who can offer a example?
the s110 v8.00 is use nrf51422,and used the ram2,
I compile the project,find...
I would like to be able to manually disconnect from a device and then begin advertising.
However, I have discovered that on disconnect, ble_advertising_on_ble_evt handler...
I have an application using N5150 SOC with S210 softdevice and using softdevice_handler, SDK 10.0.0.0, and I'm using Ant-FS to gather data from this device. I only want to...
ble_app_beacon.rar hello there i used ble_app_beacon example. i want to make some modifications. i want to put it in sleep mode after some time and again wake up after some...
Hi,
I am trying to run the example ble_central_and_peripheral_experimental (SDK 9), I program the device with S130 and the hex file. The other two devices I program it with...
Hi,
What is the meaning of "NRF_CLOCK_LFCLKSRC_RC_250_PPM_250MS_CALIBRATION"?
It means use the internal RC clock source, but what is the meaning of "250_PPM_250MS_CALIBRATION...
My application uses the WDT. In my application, I use a soft reset to enter the bootloader. Because the soft reset does not reset the WDT the program will reset while in the...
Hi, current i'm writing a program in nordic nrf51822 chip and I facing the problem of region RAM overflowed with stack after adding the BLE code as shown below :
//***...
I have a RFID application in which there is a Reader and a tag. The Reader reads the tag information once the tag is in the Reader's range. The tag is an active tag.
The...
