I'm seeing garbled/malformed UART console output when running apps on the Thingy:91 X. This includes pre-built apps from Nordic and custom apps I build myself.
Here's an...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to try out some changes that are not yet in the stable NCS releases, so I'm trying to build my Matter application using NCS v3.1.0-preview4. Unfortunately it gives...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
hi support team,
may i ask do we have demo on how to test remote provision in ncs2.9.0?
i assume there are two possiblilities:
1.
For server, we need add below settings...
Hi,
Our project need 7 seperate PWM outputs, as the nRF52840 have 4 hardware pwm, I decide to use GPIOTE with PPI to create extra 3 pwm outputs to drive Red/Green/Blue...
Hey,
I’m currently evaluating DECT NR+ using two nRF9151 DKs with the nRF Connect SDK v2.9.0.
According to the ETSI specification (ETSI TS 103 636-4 V2.1.1), the Physical...
While testing CoAP with NB-IoT I normally get PSM (sleep) delay = 20s before PSM mode is set (0.5mA with UART enabled), but after awhile PSM delay increases to ~4.5min (at...
Hi,
I recently added FOTA support on my project which runs on nRF5340 + nRF7002. I am currently working on a devboard, nRF7002DK.
Previously, I was running the project...
Since I need zephyr version 4.0 or newer, I tried updating my project to the nRF Connect SDK v3.0.0 as well as the toolchain. I know that they are not fully released yet....
Hello,
Currently the nrf-connect extension offers board targets under build configuration. These are categorized as "Nordic SoC", "Custom boards", "All". As I have understood...
After updating to 3.0rc2 from 2.9.1 Mesh example fail to build. Crypto related issues.
yml modules -
- name : nrf remote : ncs repo-path : sdk-nrf revision : 52921acad685bb3815af94d9a3a4a11ad209fcd0...
For nRF7002 the VBAT range is 2.9 - 4.5V.
Will the supply voltage used, affect the WiFi performance?
In other words, will one get the same performance by using 2.9V supply...
I am using XiP with partial code running from MX25. I am facing issue where I am getting hard faults when Erase is happening and at the same time the ISR from XiP region is...
I have a custom nRF52832 board with outputs on P0.07 P0.08 P0.09 P0.10 and I want to write to them. 7&8 are working ok but 9&10 are not.
Let me emphasise THE BOARD IS WORKING...
I need to put my external Flash into the deepest possible sleep mode possible,
I saw this api in flash.c in Zephyr, I am using the
( flash_ex_op ( const struct device...
