I am attempting to generate an 8MHz clock output on pin 2.05. I've followed an example from another post using the nRF54L, but I get build errors. The project I used as a...
Hello,
We struggle to keep LTE-M attached with nRF91 (Modem) and CMW500 (EPS) to test regular IP communication (so those are not Radio Access Network tests) during product...
Hi everyone,
Could someone help me with the following use case?
Task description: I'm working on a firmware update procedure based on the smp_svr project. I'm trying to...
Hello,
I have made a project that was based on the nRF9151 Development Kit and it works great. I had to select the -ns configuration to get anything to ever build and now...
Hi,
I bought a new nrf52840 DK board as one ofthe original nrf board of my Qorvo QM33120WDK1 kit ( 2 x nrf52840 DK + QM33120W + QM33110W) J3 connector broke. Out of the...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Through a few days of studying, I now decided that: (please correct any statements I said wrong below)
The BLE is more friendly to object oriented programming
...
I've been a little out of the loop. Can someone explain how this "drag and drop" DFU is working? And in what method iTunes is being used!?
Best I can figure iTunes is being...
Hello everyone. I am having problems using the interrups when a bootloader is programmed on the chip. My test program works fine when there is no bootloader. With the bootloader...
Hi,
I try to turn off the advertising after the first connection and then turn it on after pressing the button, this is what I wrote:
void radio_notification_evt_handler...
Hi,
I've been digging through a lot of AN's about how to design a PCB antenna, in all of them an important parameter is the output impedance of the transmitter.
So,...
Hello,
I'm pretty much new to NRF development and I'm having lots of questions trying to get a custom board to work with the provided BLE bootloader example in SDK 11....
Hi all,
Hi I am implementing MQTT client on the Nrf52 MCU, as to the MQTT broker, I am going to use the amazon AWS IoT , where the broker adopts the TLS 1.2.
I read...
I am using nRF51 and latest s310 softdevice (3.0.0) and latest SDK (v10), which is the latest compatible with the softdevice.
My device is programmed with the softdevice...
Hi,
I'm designing a 2 layer flex PCB with the nRF51822-CFAC WLCSP package and recommended ST BAL-NRF02D3 balun and on-board PCB passive antenna (not ceramic chip antenna...
Hi Friends,
I am using nRF51822(S110 and SDK10.0.0) in my project and I need the chip to be in connectable and advertising mode under peripheral config . I configured the...
Hi,
I have migrated application with freertos (S132 /NRF52 devkit ) from SDK 11.00 to SDK12.00 .
Flashed SD 3.00 and then application ,but Application is not able to boot...
Hi,
Is this the right way of reading the timer value using the capture task. In this code i am trying to read the updated value of counter for every event generated in...
Hello;
I'm developing an application that advertises as a connectable peripheral. As such, it has an ID (think of it like a beacon minor).
I have 2000 of these devices...
Does bootloader example dfu_dual_bank_ble_s132_pca10040 from SDK v11 work with softdevice v3.0?
when I try to run the dfu_dual_bank_ble example with softdevice 3.0, I got...
