hi support team,
if customer want to certificate device with 21540, which tool can customer use for dtm testing?
our tool can only set it to 8, can't be 10, as below:...
I'm developing with an NRF52832, using NCS v2.6.1/Zephyr 3.5.99
My custom hardware has three NXP PCA9538 GPIO expanders on it, to allow me to control various address and...
I think this code snippet is causing the issue, since I am able to make the device work by setting:
' NRF_SDH_BLE_PERIPHERAL_LINK_COUNT = 1' and 'NRF_SDH_BLE_TOTAL_LINK_COUNT...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Hi everyone,
In my low power application , I use PORT EVENT to detect the interrupts of my two pins.
when I use only one pin interrupt, it's working well .
But with two...
Dear All,
We are implementing 8 Pheripheral Nodes and one central node with S110 and S120 respectively.
We have our custom board with us we are able to connect the pheripheral...
Hi
I want to run RAM retention sample example with sd_app_evt_wait(void) .is it possible?
is it require soft device to load first?
I have included S110 soft device of...
Hello Nordic team,
are there documentation about the MTTF (Mean Time To Failure) Value of the NRF51822?
For more details please see the EN 13849-1. We need this information...
Hi
I want to operate nrf51 in various power modes available like low power mode, constant latency mode system idle mode and so on.my questions are as follows:
...
Hi,
I am using the following statements for send a string data over BLE.
static uint8_t Name3[BLE_NUS_MAX_DATA_LEN]= "xxxxxxxx";
err_code = ble_nus_string_send(&m_nus...
Hi.
I have interesting UART problem in Ubuntu. The multilink example only outputs one character at time, and line change doesn't change line. However if I flash another...
Hi,
We are using 52832 to developing.We need DSP to finish the arithmetic.
Can you tell me how to use the DSP on 52832 ? Do you have same examples?
These algorithms...
I have an nRF52 dev board and I'm trying to build and download some of the example programs.
The example files were downloaded using the Pack Installer in Keil MDK-Lite....
Is there any way that can allow the user to advertise a sine wave for example over a specific channel or over the three Radio channels ?
I am using S130 and Nordic SDK 8...
Hello,
As a summary (described fully below) I have loaded the ble_app_hrs example onto my device and its not working right as LEDs that should light up don't and the program...
In some of the Nordic examples I found by viewing the raw advertisements that the company ID is set to Nordic's ID (0x0059). In order to communicate with Apple devices (e...
Hi Nordic Support community,
I asking regarding LNP, Location and Navigation Profile, if it's possible to on top of nordic products? If so like which ones ?
There's barely...
Reading the documentation Address config it is clear how to use RXADDRESSES, could you please explain how to use TXADDRESS ?
As of TXADDRESS there are 3 bits available...
I am having trouble with using shockburst (based on microesb from github) after disabling S132.
When I use microesb with no SD, i just do nrf_drv_clock_init(), start lfclk...
