I used the "echo_bot sample and tried to alter it to use UART2 instead of UART0. Aftet changing the code and putting in the needed overlay, the main() program begins to run...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hello nordic team!
Issue:
I am reaching out because one of my nRF9151DK does not seem to have associated character device files created when I plug it into my laptop,...
I have an application that I want to build and run on 5 or 6 target devices including a nRF52840DK, nRF52840 Dongle, and custom boards. There are areas of the code that only...
Is it possible to see LOG_INF() or LOG_ERR() messages from custom board software when the custom board is connected to a nRF52840DK through connector P20? The custom board...
I'm evaluating nRF52840 as a candidate MCU for our next gen. electronics. I am following the DevAcademy class - all working well until I try to flash the (brand new - just...
HI,all!
I was running the nRFToolbox app on Meizu MX3 phone (one kind of Chinese phones) with android 4.5, but the app was running out of control, so my question is:
1...
I love this part (the 51822) so far. Really. However, it really lacks in the debug support department.
Keil is a passable tool. Certainly not state of the art, but I can...
I used s110 softdevice 6.0.0 and 51822SDK 5.1.0 to develop a mouse.
It can pair with ios7.1.1 of ipone 4s, but can't pair with ios6 of iphone 5, I don't know why.
Do you...
I am experiencing an unusual and hard-to-reproduce issue with some custom PCBs containing a nRF51822-QFAA, S110 v5.2.1, with 10K external pulldown on SWDCLK, and a 10-pin...
Hi Nordic team,
I intend to use RFID function on the BLE technology. Related to your product, could I:
Use nRF51822 as the reader to detect the attention of some...
Hello, I am writing a fairly complex application using the Arduino SDK and an nRF8001. I have a lot of what I want to do working based on looking at the code in the different...
Hi All, I am a newbie....What is the starting point and procedure to develop nRF51822 working with Iphone or Android over HID protocol? Is there any example?
Is it too tough...
Hi,
In the API, the user gives the 'distance_us' parameter for the next requested slot. I have noticed that this is quite accurate (to the micro) and wanted to know if...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi All.
I made my PCB with nRF51822 and achieved around 150 Feet range (LoS). My target is to calculate a approximate distance (in Feet) from RSSI values.
I did a field...
I want to set up the HRS demo, but in reverse. I want to use my PCA10001 board to receive heart rate data from a peripheral device (already working and tested on my PC). It...
Hi,
i have a problem in my Code, when ic look nrf_delay_us (1000) on the oscilloscope i can se a puls withe 1,3 us thats not accurate enough. What could be a reason for...
Hi,
I have created Eclipse project to compile nRF51 DFU loader. This is a pure Eclipse project, no makfile. It has compile configurations for combination of Single/Dual...
Hi,
I am looking to build a beaon product based on nRF51822. There are several kits available shown below. Which kit should I pick to start the hardware design and firmware...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
