Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
In some case sd_nvic_SystemReset() can not reset?
nrf51822 S110.
for example:
void main(void)
{
sd_nvic_SystemReset();
do something;
}
It can do somthing!!
So sd_nvic_SystemReset...
Hi,
I have just bought NRF51822 without any extra peripherals(no motherboard/DK). Just plain Module like below image.
I am supplying 3.3V to VDD and also Connected GND...
Hi all,
I find a problem when testing the ANCS program. It seems that after you connect the device with ANCS with an iphone, you cannot connect the device with another iphone...
I built the ble_app_proximity project and down load into my board, it can advertise and can connected by the lightblue and the nRF toolbox, But i sent the hex value of 0x02...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
Hi,
I am currently working on a project with nRF52 preview DK.
In my system, an ECG chip is used to measure the heart rate and the data will be transferred back to nRF52...
Hi,
I have a number of products with nRF905 successfully deployed. Now, I am in a little struggle with a new one. The problem is the signal strength. The other products...
I'm trying to add a feature where my peripheral will temporarily trigger a Faster Connection Parameter for a period of time determined by an app_timer. However it seems that...
Hello Nordic Devzone.:
When studying the 8.0 BLE Central multilink example (s120 softdevice), I looked into the component relevant to button pressing interrupts, app_button...
How do I use the NRF51 or 52 to create a GATT server with read only service without requiring bonding? Basically I want to be able to provide more data than advertising allows...
I can not connect to one of my beacons, i need to reset its config, but HW way.
Can i reset it somehow?
It is nRF 51822 based, sensoro 4AA. I asked sensoro 3 days ago...
Hi Nordic guys,
we are using uart for communication with another MCU and flow control is used.
Beside the uart communication itself we have out of band signals (on gpio...
Dear Nordic.
I have used to nrf51822 custom device. I confused it because of Uart RX data.
The master device sends blow raw data to client device(nrf51822 custom device...
I'm trying to compile a program on mbed for a BLE Nano, which uses the nRF51822. I've included the nRF51822 library by Team Nordic that's listed on mbed's library wizard and...
Hello
i am trying to upgrade from sdk 9 to sdk 10 .zip version but after installing when i open some examples it asking me to install arm cmsis 4.5. pack and device family...
