Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I'm new with a) the Nordic Softdevice environment and b) using the nRF52. So there are a few questions...
As a starting point I've used the template project (.....
Hello everyone ,
i am trying to increase the sound of the buzzer so can anyone suggest me do i ahve to increase the supply voltage or do i have to modify the dutycycle...
I have now used days trying to create a working clone of "dfu_dual_bank_ble_s110_pca100028" so that the source would compile and result would work correctly, independently...
I have 5 LEDs - ideally I would like to control the brightness of each one independently (i.e. 5 PWM channels). I'm using SDK 9.0 and SD 310. I have been looking at the PWM...
Hi,
I got the ble_app_beacon_s110_pca10028 from Keil_v5 Pack Installer to compile. I followed the step to use nrfutil.exe to generate a zip file. But when I did the DFU...
I can't afford nRFgo Starter kit as of now; so my question is if there any other way to program my application (firmware) in nRF8001? I am looking from following options:...
Hi,
File "nrf_drv_config.h" defines both TIMER1_CONFIG_BIT_WIDTH and TIMER2_CONFIG_BIT_WIDTH as "TIMER_BITMODE_BITMODE_16Bit", can these timers be configured as 24 bit...
HI,ALL,
I want to take use of hardware flow control, but when i set or clear the RTS signal, it failed.
something about the attempt as following:
the purpose:enable the...
Dear all,
I'm using an nrf51822 (running softdevice 6.0.0) with the proximity profile.
With iOS8, I was able to find & pair my device with the nRFproximity app.
After...
Hello from Spain!
It is my first time that I use a Bluetooth chip so I am following all your code stack and some answers of this portal, but I am having problems with the...
Hello everybody,
I am using RTC1 for time measurement, this works fine as long as no BLE communication is running.
The RTC is initialized with
const nrf_drv_rtc_t...
situation:
We are developing an nRF51 application with OTA DFU. we use SDK 9.0.0 and the DFU bootloader version is v8. We have prepared different two packages. Single OTA...
phenomenon:
the program is polling in the 'uart_event_handle'
my attempt:
i found that the 'uart_event_handle' is called by the 'uart_event_handler' , so the program...
I would like to know how can I use nrf52832 preview kit for audio application, i.e. I would like to use PDM interface of nrf52832, please guide me on how can i do that.
