It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hi.
I use nRF52 and I want to use DFU.
I want to make init packet because DFU need it.
To make init packet,
need master control panel.
I want to know how to get...
Hi There,
Is it possible to modify the number of BLE frames per connection interval (CI)? We are using nrf52832s and are only seeing one master request and slave response...
Hello,
can anyone tell me something about the security level of the connection like it is made in the Heart Rate Sensor Example. Is the connection encrypted or can everyone...
Hi all, I'm working on SDK11.0.0 experimental signed bootloader, I stored device type and device revision in uicr register now I need to update my bootloader through dfu and...
hi everybody.
Please help me on this
I use nRF51822 as iBeacon with ble_app_beacon in Nordic DK in below state:
only advertise in iBeacon mode
interval = 100...
Hi
Can we have both bluetooth and Gazell enabled at the same time?
We are using nrf51 series chips.
We want Gazell to communicate with with other nrf chips and Bluetooth...
I was searching the way to make example code ble_app_uart passkey pairing, while reading the documentation i found that function sd_ble_gap_authenticate() can be used to configure...
I'm trying to read a byte using uart, I'm calling app_uart_get from main loop, but it return always NRF_ERROR_NOT_FOUND . I checked with oscilloscope and I can see the frame...
Hello,
we try to use static passkey protection on our devices.
we use nrf51 sdk12 with s130.
We read a few threads for setting a static passkey like here , here and some...
Hi guys, I'm migrating my SDK 10 project up to SDK 12. There are quite a few new configuration files and setups. In order to enable app_pwm peripherals I enabled the proper...
Hello when I tried to use IronPython with MasterEmulator.dll in example as described in documentation. I got following error:
c:\Program Files (x86)\IronPython 2.7>ipy...
I'm tying to read and write external memory using Spi bus
when I flash only the softdevice and the app, the program works fine
but when I flash the bootloader, the program...
I'm trying to flash the bootloader on an nrf52 device. the microcontroller is detected successfully with segger. but then when I flash the bootloader given with sdk11 (dual...
Hi,
my device : nRF51822 with sdk 10.0
Before I talk my question, let me make clear.
When peripheral connects to iPhone, it's on iOS's setting too but it doesn't go...