I have been following this tutorial by Nordic trying to install nrfConnect for VS Code, nRF Connect for VS Code, part 3: Building an application , but I am facing several...
Hi,
Tried to use Connectivity bridge app on a custom board based on NRF52840 and it seems that the UART-USB interface works initially, but after a while it gets stuck at...
Hello, I'm trying to use BLE on nrf52833. I'm developping with segger embedded studio and I' m usign the BLE peripheral example "ble_app_blinky". Firstly I erased the flash...
Hi DevZone team, I have a question on the Segger RTT...
I have rtied to use it with NCS 2.9.0-nRF54H20-1 but Segger RTT Viewer said that it does not know such kind of...
Hi
I am using nrf70-wifi-ble-image-transfer-demo in the nRF7002 DK.
I deleted all the mega camera stuff as I want the MCU read image from another stm32, I successfully...
Hi NRF team,
I am working on a patient monitoring system where we have used a stereo microphone. I am using the LC3 compression method and the Zephyr PDM microphone driver...
Hello,
We are developing a system that have the nRF5340 as a part of several MCUs, and we want to be able to upgrade both cores.
According to this: DFU for the nRF5340...
I am using NRF52 S132, and using UART service , but my phone is getting disconnected automatically after 1 or two minutes. I have seen this question asked in Forum but that...
Hi,
Has anyone test with Nexus 5X ?
I could not change connection interval 7.5ms, the interval is always 45ms.
Does anyone know how to change the connection interval...
SDK 9.0, examples/ble_peripheral/ble_app_hrs
Trying to use DFU with a bond device, I got aware, that after the update, some "static" data seems to get corrupted during...
In the Keil Pack nRF_Libraries V3.10 [SDK V10.0.0?] (Low-Power PWM Example)
Not a big Bug, but an inconvenience all the same.
low_power_pwm.c line 165
ret_code_t...
Hello,
I want to change the advertising timout during runtime. We have two use cases for our device:
Batterie mode --> advertising timeout = 2min
Power...
Hello,
Implementing a LED led driver was pretty simple and below code works well:
nrf_gpio_cfg_output(LED_PIN);
nrf_gpio_pin_clear(LED_PIN);
NRF_GPIOTE->POWER =...
Hi there,I am using the PWM library in github github.com/.../nrf51-pwm-library . After I do this in my project and I check the pin output with Oscilloscope but didn't see...
I have a product that was released a few months ago and is operating in-the-field. Recently we discovered a bug and need to fix it. We are unable to do a DFU because:
...
Hello,
DEVICE_MANAGER_APP_CONTEXT_SIZE should be less than 256 bytes in size.
However, it seems to work properly (not fully tested) whith a size of 800 bytes, and no more...
Hi all,
I want to make sampling from microphone at 16KHz. So I want to first disable softdevice, do all measurements. An after that enable softdevice to transmit data. Will...
Hi,
Recently, I am playing around with the NRF51 dongle and trying to make it work as a BLE master.
However, when I run the sample code(e.g. advertising, multi-link .etc...
Hello, i am seeing a strange behaviour of pstorage module and i don't understand what is happening. I have read links below:
pstorage-problem-on-power-off
saving-data...
Hi,
I haven't been able to find a clear answer to this.
With the ESB protocol, a payload can be stored in the PRX TX FIFO to be sent back to the PTX as part of the ACK...
I have some nrf51422s beacons and wondering if they can send and receive data. So I want it to keep transmitting its id and signal strength but if somebody is reading the...
