Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
Hi,
On the ANCS example the flag LIMITED_DISC_MODE is set, but when I sniff the adv packets they have the flag off. This is both when is fast or slow advertising.
Am...
Dear all, I wanted go a step forward on BLE services and characteristics trying include two characteristics on a BLE
service, I think one of best examples is Github ble_app_lbs_master...
Device : PCA10028 + PCA10031
tool: Keil free (32k)
Objective : to learn to write BLE apps using Nordic 51822 QFAB chip (I designed a prototype board with this chip, but...
nrf51422_xxac.hex board = for nrf board PCA10028
use sdk 8.1.0
error for dual_bank_ble_s110/armgcc/_build/nrf51422_xxac.hex
use master controll panel version 3.10.0.14...
Hi all,
I am currently developing a firmware on an nRF51422 which supports ANT communication with softdevice S210 and that lights up WS2812 LEDs (or Neopixels). To light...
I'd like to get a notification every time after the radio has been active (as shown as NACTIVE in the S110 rev 1.3 spec). How can I make this mappen?
I see two functions...
Hi,
Using S130 via mBed, I'd like to have a fairly large number of characteristics (say 30). Unfortunately this seems to be too many, as sd_ble_gatts_characteristic_add...
I have compiled two projects namely Blinky and ble_app_template.
Both projects run and debug but the radio portion in the ble-app_template is not functioning.
Having a compiled...
I have been reading a lot of post about static pairing passkey using S110. I have tried two example provided in this threads: devzone.nordicsemi.com/.../ devzone.nordicsemi...
Hi,
I have done the bonding and saving context to flash. As an example I used ble_app_template. I cutted all redundant code and limited to single bond for simplicity.
In...
I am trying to communicate between nrf51822 and Android device using Gatt. But nrf51822 invokes UartService.ACTION_GATT_DISCONNECTED after some time, the disconnection happens...
Hi,
until today we develop our application on Nordic DK with nRF1422 with 32 KB of RAM.
We are using S130 and SDK 8.1.0.
Today we saw that our target module, the MBH7BLZ07...
Hi!
I'm working with nRF51DK with s110 soft device on it. I'm trying to write simple custom service which reads some data from sensors and send it over BLE to Android app...
Hello,
I know the current limit of 15mA to share among all gpio pins.
If I source/sink current in very short bursts (100ns every 1ms) can I draw larger currents than 15...
Dear All,
We are working on a custom board with NRF51822.Everything works fine apart from the timer. What we are doing is that once the board is booted, it reads some values...
