Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
We have peripheral, and we want to connect it using NRF 52840. when we are bonding this using nrf connect app we get a pop up with random key and using pair we can pair with...
I'm using the nRF9160 with the LIS2DH accelerometer and SDK version 2.5.2 . In my hardware setup, INT1 is connected to GPIO 0 and INT2 to GPIO 1 . I'm configuring both interrupt...
Hello,
I am currently using the `AT%XICCID` to obtain the ICCID of Hologram eSIMs. The output of some of these eSIMs are just the raw 20 digit ICCID with no ending checksum...
Hi,
I’m looking for your recommendations on a suitable conformal coating for an application subject to high humidity. The goal is to mitigate any potential risk of short...
Hi I am trying to get an SD card hooked up to my nrf52840 devkit. I am using nRF Connect v2.6.1 and I was trying to get the sample code working, so I used the sample in ncs...
I have downloaded nRF connect setup V5.1.0 and nRF command line tools V10.24.2.
downloaded nRF connect extension , SDK pack and tool chain in VS code.
I added the build...
in this example:
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/bluetooth/conn_time_sync/README.html
the peripheral has this assert statement when...
Our design has an nRF5340 with RV3028C7 to provide the 32 kHz clock via P0.00.
If I configure P0.00 as a digital input, I can see the pin toggling.
However, if I use the...
Hi
Is it possible and what is the correct way to implement main clock trimming at runtime? Which NCS version this works on?
I see there is already some setup going on...
Hi,
I want to write data to a specific memory. I understand there is ZMS.
https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/samples/subsys/fs/zms/README.html#zms...
Hi,
I am trying to build memfault sample as in intermediate course, after hello_world project configuration and prj.conf options addition, i get following build error...
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
Setup: NCS v2.8.0 nRF52840
Hi,
I would like to ask about the implementation of Zephyr's SAADC driver (` adc_nrfx_saadc.c `).
In the project I'm working on, I need to...
To read the MAC addresses defined I use the following code (with CONFIG_BT_ID_MAX =2 in prj.conf):: :
bt_addr_le_t addr [ CONFIG_BT_ID_MAX ]; //space for random address...
Hello everyone,
I have an nRF5340 microcontroller (NORA B106 module), and I want to connect a square wave signal to one of its pins to read its frequency or count the number...
