Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi,
I've developed an application which sends sensor data through the BLE interface at maximum available bandwidth by checking the BLE_ERROR_NO_TX_BUFFERS return value...
Hello,
I was wondering if anyone has had success communicating with the nRF24L01+ eval kit and a Raspberry Pi. I have found several examples through Google and am trying...
I am requesting the softdevice to start/keep the 16Mhz crystal oscilator running with the following code:
// Request 16 MHz crystal oscillator
err_code = sd_clock_hfclk_request...
Hi,
I have Nordic Nrf51822 custom board.
in that we have spi Nor flash.
i check the spi read and write with an application without soft device enabled.
which is...
Hi all,
I'm having problems when linking my code intended for use on the nRF51822. For some reason there are missing symbols that are needed. I've traced the dependencies...
Hello,
Does Keil's Lite/Evaluation MDK-ARM tool chain version suffice for development work on nRF51 devices? Please advise!
I have seen questions about using GCC and...
I'm using the s110_nrf51822_5.2.1_softdevice with the NRF51822. If I understand correctly, after pairing the NRF51822 with a phone, a long term key has been generated and...
Hello,
I decided that bonding (does it equivalent to "pairing"?) is not allowed in my application, so I modified the following definition in main.c:
#define SEC_PARAM_BOND...
We are trying to get the ANT feature to run based on RTC as follows:
a. Timer RTC0 or 1 (1 for this example - tick is disabled, compare is on.)
b. Timer initialized (all...
Hi,
I'm a new learner for the nrf51822. In the SDk ,there is an example of esb which is used for the radio transmittion with ACK. I want to know that if I can use the esb...
We have a custom board designed based on N51822, CEAAB0 and we have used the chip antenna from ST BAL-NRF01D3. When we have flashed our proximity code to the device, we will...
Hi,
After i use sd_ble_gatts_hvx() ,i will receive a BLE_EVT_TX_COMPLETE.
The "tx_complete.count" is no problem when i use softdevice 5.2.1 . e.g. count =1. this is correct...
Dear Sir,
i am using pca10001.
Actually i tried to read and write the data from EEPROM having address 0x50 though i2cbus.
i made po.0 and p0.1 as output pin then...
Hi,
I've created a small test program (pasted below) that is intended to help me profile some of my code down to us resolution. Maybe you can quickly run it (no other files...
