Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Hi,
I set advertising data as follows:
err_code = ble_advdata_set(&advdata, NULL);
But I can't achieve advertising without ScanResponse，could you give me some suggestions...
Hello,
I do connections between 2 nrf51 with a known and static services. Is that possible to bypass the discovery to access a characteristics (i know all characteristics...
Hi,
I am having problems using the the dfu_dual_bank_ble_s110_pca10028 example on a nrf51822_xxAA device.
I have changed the memory ares to:
IROM 1: 0x3C000, 0x3C00...
So long story short - I need to pair two devices: Arduino UNO with Seeed BLE Shield and Adafruit Feather 32u4 Bluefruit LE.
Now, Seeed shield is configured, and is able...
Hello, I am now having problems to get NRF51 DK to work. My computer is connected to board with USB. It can recognize it.
Now, here is what is something strange, when...
Not sure if this is the correct place to ask this question.
I can't seem to find the download location for the Master Control Panel PC application. It seems to only available...
Hello,
I am currently trying to generate a PWM signal on P0.00 and am not having success. If I drive P0.00 without PWM, everything works fine. Is there anything that would...
I have 2 nRF51 Development kits and a nRF51 dongle that I am using for proof of concepts. I am mainly using the nRF51 IoT SDK because we are looking at using IPv6 with 6LoWPAN...
I'm looking at log_uart_init in the nRF5_SDK_11.0.0-2.alpha and wondering if it would make more sense to allow the application writer to pass in a baud rate.
I'm trying to program a nrf51822 custom board using the SWD interface of the nrf51 DK. The board is using the low voltage configuration.
I'm not duplicating this question...
The IoT SDK Documentation page is getting Error 404 not Found.
Here is the error:
The requested URL /nRF51_IoT_SDK/doc/iot/html/index.html was not found on this server...
I know the softdevice region in the nrf51 is determined by the CLENR0 register.
But I read that the CLENR0 register is removed from the nrf52 and the MWU can be used to achieve...
Dear Sirs,
I buyed recently a Bluefruit LE Friend based on chip nrf51822. I triyed to get working with the ble-sniffer without success.
I don't have programming interfaces...
HI,all,
MERRY CHRISTMAS!!!!
i have an issue when i want to try the data transfer using timer
i have a idea about it , but i do not know how to achieve it.
-my project...
