Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
We recently received an eval kit the the nRF52832, but we were told not to take current measurements with this version. This presents a problem since we are evaluating...
I am using this mbed workthrough, to create a custom GATT Service in C++. However, this code only creates characteristics with UUIDs:
uint16_t percentageUUID = 0xA002;...
This thread mentions having the master read the DFU Revision Characteristic to determine the DFU revision. I've based my DFU and application off the dfu_dual_bank_ble_310_pca10028...
Could you estimate the free space for Application on nRF51 and mRF52, on this case for Homekit with FOTA :
Boot Loadeer with FOTA
Homekit Enable
BLE Software Device...
What are the options to update firmware (Application/Bootloader/Softdevices) for multiple devices built on NRF51x22 ?
Using Master Control Panel could take days programming...
Dear Nordic Team,
I am using HID mouse example code in my nordic dk board.
I can able implemented fallowing logic in my code to do left , right and middle button click...
Hi,
I am using nRF51422 with SDK 9.0 and SoftDevice130 with nus service. I have a custom android app running on BLE uart service. Data communication and connection handling...
How to save the uart app on my nrf51dk board? it only runs when i connect it with the usb. another question nrf51dk have a nrf51822 chip(SoC)?
please help me out. i want...
Hi,
I have installed EmBlocks 3.2 (the last one) but only extremely simple examples will compile.
It appears that the support files in wizard/arm/nordic/nordic.zip/Common...
I have been struggling with the custom characteristic implementation. I have followed the great tutorial on custom service that is online but there is really no doc or information...
The nRF Beacons iPhone or Android app requires adding a new beacon devices in order to notified events. Is it a must for beacons? Or is it just a one step for examples. In...
I try to advertise with a custom UUID and I do not know how to do it.
The standard services works with 16 bits and I need to work with 128 bits
So how can I do it?
Thanks...
Dear Nordic family,
I am using Bluetooth Low Energy, Beacon module with ARM Core from Tindie ( Product link ). The reference manual from their website is attached IMM-NRF51822_RefMan...
I am trying to work on ble_app_uart example project working.
I am able to see that the "nus_data_handler" is triggered when any data is received over the BLE channel. On...
[Duplicate question. See the original post here ]
Dear Nordic team,
I have purchased Bluetooth Low Energy, Beacon module with ARM Core from Tindie
They gave me...
