Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
hey,
i want to discover the PCA10001 board with PCA10000 board in master emulator. i have programmed the blanked PCA10001 chip with softdevice(s110_nrf51822_6.0.0_softdevice...
I want to generate PWM.
I set timer2 events_compare[0] to toggle pin 1:
sd_ppi_channel_assign(PWM_LED_HI_CHANNEL, &(NRF_TIMER2->EVENTS_COMPARE[0]) ,&(NRF_GPIOTE->TASKS_OU...
hi, I have posted a detailed problem using Eclipse on Vidar's tutorial.
Any help is appreciated.
See following link:
devzone.nordicsemi.com/.../
Thanks!
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
I want to send a data of length 1024 bytes over the ble UART , but the maximum length of data is 20 bytes at a time. Is it possible to increase the data length per instance...
Hello!
I try to use "ble_default_bootloader_app.hex" with my app to allow OTA option for my device. (nrf51822 and SDK 7.2.0) With NRFToolbox I can connect to the device ...
Hi all,
How can it be that sd_ble_gatts_sys_attr_set function returns BLE_ERROR_GATTS_SYS_ATTR_MISSING?
With the first and second connect it returns success but the...
I saw that each CCCD or sys_attr should be persisted per connection, does it mean it should be saved on flash to be restored during next connection for same device ?
and...
If iOS of BLE master sends 4 packets of the same write characteristics with MD bit in the same connection event, how does SoftDevice of BLE slave work?
The ble_event_handler...
Is there a summary of potential pitfalls, i.e. issues which are asked repeatedly by users in these forums regarding HW/Schematic/PCB design for NRF BLE chipsets. Making mistakes...
I just published my port of a new FreeRTOS operating system version for the nRF51x22 and the nRF51 SDK 8.x.x to github.com/.../freertos_nrf51 , the README is copied below...
I am trying to implement some write to flash, and started by integrating the relevant functions from the example code I found in this thread .
I added a dummy write function...
Hello,
I'm building an aplication with multiple nRF51822 beacon modules. I'm using dual mode S130 softdevice. Sometimes, when beacon recieves a lot of messages, and forwards...
I'm trying to erase the page 32 of a nRF24LU1+ via SPI (using a Bus Pirate).
What I did so far:
Display the first 16 bytes of content of page 32: 0x03 0x40 0x00 0x10...
