Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Dear Nordic support team,
What is the maximum number of timers that I can create (and use) using the app_timer lib?
err_code = app_timer_create(&m_timer_m_1_0,
APP_TIMER_MODE_REPEATED...
I've recently started sharing development activities with another developer. I created a GIT from the folder: C:\Keil\ARM\Device\Nordic\nrf51822\Board\pca10001\ble\myProjectFolder...
I'm leveraging off the heart rate sensor example to create my own VS service. I've successfully registered a 128-bit UUID with the Soft Device which is enumerated along with...
Hi,
i get the example for using PWM to run and modfied it to use it in my application. My Prolem is that i only have one PWM Output toggle Pin. How can i build a second...
Hi,
I'm using the MCP to send a long to a nrf6310 board loaded with SD v6. The board hangs when I send a long though, is this due to the MCP not being set up to send longs...
Hello,
I have the nRF51822 Evaluation Kit. I have run the basic code examples like 'Blinky' and the BlueTooth HRS (Heart Rate) application, successfully.
Now I would like...
Hi,
Is it possible to give a function address to the "Task End-Point" of a PPI channel?
Like :
err_code = sd_ppi_channel_assign(PPI_CHAN0_TO_TOGGLE_LED,
&(NRF_TIMER1...
I am designing a device that needs to operate both as a Peripheral (such as a Heart Rate sensor) and also as a Central so it can optionally connect and gather data from other...
Hi,
in my application I have a device that has to be controlled by a remote control. For transmitting data between the remote and the device I would like to use BLE (not...
Hello,
Can you please help me with the following questions....
Why table 3 in the softdevice spec shows the same address for the application code_r1_base when softdevice...
I'm having a very strange issue when trying to debug application code on my Nordic platform. I'm hoping that someone else can shed some light on the issue, or at least confirm...
Hi all,
I have followed the guide (AN-29) for using eclipse with the nRF51822 but it gives me several errors.
First at all, the linker says:
...../arm-none-eabi/bin...
Is there an example code anywhere for the nRF51822 to calibrate the internal 32khz RC oscillator using the 16mhz crystal when not using the BLE stack/softdevice?
I would...
