Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
At present time I perform many tests with power level and link stability. And noticed that if cover nRF base device with hand or put into pocket the disconnection with...
Hello,
Is there any way to configure the flash data default values during programming phase with Keil IDE?
In IAR, it is possible using a file ".s43" included in the...
Hello, I'm using the nRF51822_QFAA chip on a custom board, but the layout and parts are the same as on the nRF51822 USB dongle . I tried flashing the Board\pca10001\s110\ble_app_hrs...
I am using nRF8001 with EMF32.
inside hal_aci_tl_send function
C : 1, 14,
inside hal_aci_tl_event_get function
E : 3, 132, 128, 130,
It is looks like
Length == 3
...
Hi,
I am working on a small (1 inch square) bio-sensor project that needs Bluetooth capabilities. I like the nRF51822 and was looking into the dev board ( www.nordicsemi...
Hi
I am setting up a production programming script, and would like to know if it is possible to write short strings or numbers directly to flash. For example, i would like...
I use an ISP 130301 Development Kid for getting familiar with the nRF51822.
I flashed SD110 on the Demo Board with nRFgo Studio and compiled and loaded the proximity example...
Hi, I have a project where I need to communicate using UART BLE between nRF51822 and a PC ThinkPad with Windows 8 and embedded BLE4.0 hardware.
I have programmed the nRF51822...
I'm running into a hardfault. I perform some initialization and enter a main loop. At the end of the main loop, I put the soft device into sleep mode and wait for an interrupt...
Hi,
Recently I updated my SoftDevice on beacon from 7.1.0 to 8.0.0. Unfortunately, I met the same problem with advertising timeout which I faced with in SD 7.1.0, but the...
Hi all,
I have some doubts over the memory management of nRF51822 and nRF51422-EK.
I have gone through the link in this forum where it is explained buy I'm still not sure...
I'm trying to build a project of "nRFUART_GoogleAPI_Android4.3+" from the following link.
[https://www.nordicsemi.com/eng/Products/nRFready-Demo-Apps/nRF-UART-App2]( www...
I have one doubt after reading the definition of PSTORAGE_MAX_APPLICATIONS and PSTORAGE_DATA_START_ADDR in pstorage_platform.h and the actual computation of used flash memory...
MCU : NordicSemi nRF51822-QFAA (Using custom board)
SDK Version : 7.2
Softdevice : S110 7.1
Using IAR for ARM 7.1
Hi, I was migrating my codes (SDK 6.1 to 7.2...
I am using the ble_app_template, together with one timer called every second. The timeout handler of the timer just prints a short string on the serial port using simple_uart...
