void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi Team,
What if I don't what to use BLE stack but still want to use nRF51 Radio (PHY + MAC) to implement some custom communication protocol between multiple nRF51 devices...
i am new at this so please bare with me.
i was using a nfr51822 with s110 version 7 and i now i want to migrate it to s110 version 8.
i have made a few changes according...
After checking bootloader example from the SDK version 10, I am not able to find appropriate ROM / RAM addresses configurations for 16kb RAM chip. The Bootloader examples...
Trying to run S130 V2.0.0 with ble_app_proximity on a BLE400 motherboard.
Im getting a hang at the call to SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM, NULL...
Hi,
We just received our custom board based nRF52832, below nRF52832 schematic
I succeed to flash the board. but i have frequency troubles.
I made a simple exemple...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I have opened the nordicID sample project "InventorySample" for Windows CE in VS2008 it successfully builds the project but when i deploy it on mobile simulator Pocket PC...
Hi,
I'm using S132 v2.0.0 and nrf52832. I've got a problem when I'm trying to call any softdevice function from radio notification event handler.
#define RADIO_NOTIFICATION_IRQ_PRIORITY...
I am using nRF52832 DK and we designed a custom board using nRF52832. I am using a windows 10 lap. It used to program successfully from windows 10 lap and boards will advertise...
Hello,
I use nrf51 based device as peripheral with SD110.
I use connectable advertising ( BLE_GAP_ADV_TYPE_ADV_IND, BLE_GAP_ADV_FP_ANY ) and turned on BLE_GAP_EVT_SCAN_REQ_REPORT...
Hello,
what address in flash is it safe to store my application settings (some calibraton data) which should be preserved during application updates. I use S110 v8, dfu_dual_bank_ble_s110_pa10028...
Hi all, i'm trying to understand how to program my nrf51 DK in order to perform a temperature measurement with the onboard sensor, convert the battery voltage with the ADC...
I use dfu_dual_bank_ble_s110 bootloader from SDK10. I want the bootloader to check whether if incoming firmware is compatible with the device it is uploaded to (i.e. device...
Hi
I want to connect to only a single master device by s110. I used the example parameter setting from "ble_app_hids_keyboard" for gap_params_init, advertising_init and...
I have modified the Android Blinky App to connect two peripherals (nRF52 DK)
Scanning and Connecting to two peripherals works.. but when i want to start sending notifications...
