VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
For nRF51 series chips and S110, S120, S130 soft devices.
Is it somehow possible to have a connected ble peripheral while broadcasting data?
S110 spec doc says "broadcaster...
I'm a hardware/beginning software guy just getting the nRF52 up and running using the Keil uVision5 tools. I go to debug either the blinky project or heartrate project and...
I'm planning on testing an rf link with just a pair of NRF24L01+. Having battled with the PTX side and got that working i'm looking at pipes an addresses.
An answer to...
Hi,
Since version v1.16, nRFGo Studio don't start.
The installation is correctly done, but when I launch software nothing occured. I can see it briefly in process list....
The GCC linker scripts included with the nRF51822 SDK (checked: 6.0.0 and 6.1.0 as well as nrf51-pure-gcc-setup ) include .init_array sections , but do not specify them as...
Why does the soft device raise a SWI2 interrupt to indicate to the application that an event occurred? In the SDK, callbacks are implemented using function pointers. A function...
Hi!
I'm launching code from example to NUS (ble_app_uart) on nRF52-DK. Everything is going OK, except when I quickly send 4 packets in row from UART to connected Bluetooth...
Hi,
I'm currently working on the project with some hard-timing dependent features. As I've mentioned in another topic, it fails if I have advertising turned on. Turning...
Hi, after I updated my MAC OS X to the latest version EI Capitan, I found my JLink commander cannot connect to the PCA10001 board again even with the Jlink commander updated...
I read somewhere that to get the callback working on pstorage write, read etc, you need to call pstorage_sys_event_handler() in a function set by softdevice_sys_evt_handler_set...
Hi,
Each Gazell device has unique address identifier (i.e. base address + prefix) mapped for each pipe. How about the host?
For example:
Device that transmits on pipe...
Hi,
Each Gazell Device has an unique address identifier (base address + prefixes), what is the default address identifier for the HOST?
For example
Gazell device transmits...
Hi,
I'm having trouble with how to begin debugging a hard fault error in my code. When I run the debugger, it always ends in the HardFault_Handler in arm_startup_nrf51.s...
I am developing a project by employing nRF51822 and my code is based on ble_app_uart. I met an issue that if there is no device connects to nRF51800 in 3 minutes, the program...
