I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
Hi All,
I just bought the Nordic Semi nRF51822 DK (without the starter kit). I tested the Heat rate monitor app and it worked fine. It could send some random values to...
Dear all,
I tried the example program ble_app_uart given in the examples section of the Nordic folder in Keil installation. I created the hex code and programmed my chip...
I was just at the Nordic nRF52 Global Tour in Atlanta and I received the nRF52 Development Kit (PCA10040). One of the Nordic engineers mentioned that the nRF52832 is at rev...
Hi all,
I am using the BLE nRF8001 and EFM32 (ARM Cortex M3). I used the following SDK for connecting the modules using ACI (SPI). github.com/.../ble-sdk-efm32
Now I...
brownout reset = 1.7V
Operating conditions VDD(Supply voltage,internal LDO setup) = 1.8V
(by 1822 Product Specification)
In between 1.7V of 1.8V, or it would have been...
Greetings, I've been using the ARM GCC tools for about 2 months with success for programming the NRF51 DK board. Now I would like to try out the example found in:
examples...
I run step by step the example of adding DFU to ble_hrs, everithing runs fine.
I try to change in the same way another example, ble_app_proximity.
The problem is that...
Hello everyone
i have created one custom service and i succed to compiled then i checked my service via master control panel it is showing unknown service but i named it...
Hello,
I have a question about including multiple identical services in GATT table. For example, my device has 2 batteries so I need 2 battery services (with same UUIDs...
Hello,
I am developing a NRF51-based peripheral (S110) device with N tactile switches - each one assigned to single "bonding slot". I need the peripheral to be able to...
i have use nrf51822
when no connection creat between android nrfUart app and backon kit so autometically sleep in 180 seconds,
but i have need sleep condition in connected...
I'm new to the Nordic range of devices and the SDK.
I have a project where I'm using the HAL in the SDK to configure GPIO/GPIOTE and the UARTE0. With both the GPIOTE and...
Just want to check that my understanding is correct:
I have ported/migrated my app from SDK 6 to SDK 9, merely because I want to use the DFU facility. However, I have read...
Hello everyone
i am trying to add printf statements inorder to see the excution of the program can anyone sugges tme how to printf statemtns in app_uart example!? i would...
