I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hi,
my task is to develop a "repeater" and I have three nRF51422 evaluation kits.
For example, one of them sends a file, the second one receives it and then sends it to...
Hello,
Using the "simple_uart_get_ with_timeout",I cannot receive a "frame" bigger than 6 bytes.
Why?
while(simple_uart_get_with_timeout(1, &UART_RX[receivedBytes]...
I have a simple app that send button press/release events to a smart phone. One of the buttons doubles as the wakeup button. I would like to qualify the wakeup button press...
The documentation for S110 v7.1.0 sd_nvic_ClearPendingIRQ implies that it works with any valid IRQ.
I find that (using S110 v7.1.0 with SDK 7.1.0):
sd_nvic_ClearPendingIRQ...
Hello,
I'm currently reading nRF51_Series_Reference_Manual_v2.1.pdf. On page 28.9.9 there is the UART CONFIG register documented. Two bits of configuration for the Parity...
Hi,
Tried to develop an application to read current time characteristics from central device (ios app) by using nrf51822 peripheral device(s110_nrf51822 v7.0.0.). After...
Dears,
There is a problem as the subject. I am using the reference code of ble_app_hts to add an app timer for a service. the device of nRF51822 can be searched and connected...
Hi,
I'm really new here, sorry if it is a beginner question.
Our company wants to start developing a RTLS (Real Time Location System) to track mainly person (patients...
There are a few threads on using the AES module and there is a lot of confusing and somewhat contradictory information.
I want to do the following:
generate secure...
Hello,
i have an application that sends periodically sensor data from one sensor network (6 sensors - 16 Bytes) to a host f = 1/4 - 20 Hz.
I read the s210 and s110 SDS...
Hello, I'm using the nRF6310 board and tried the HID Keyboard Application
(S110, ble_app_hids_keyboard) example.
The nRF51 SDK version is 6.1. I use IAR for ARM 7.1. ...
Dear,
We are developing the nRF51822 for an application of BLE device. The timer is the key process in the application. Anyone kindly share the experience with me about the...
I have a test set up using the ble_app_hrs example where I increment a dummy uint16_t periodically and then send that value up to the nRF Toolbox iOS app to plot. I want to...
Hi all,
I would like to use the strcmp - string compare function, however don't know how to create a string from character array. Standard way would be something like this...
