But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine if we can use one Ignion antenna, shared for the LTE and GPS.
On the original...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
I've been trying to flash an nRF52840-DK with code that successfully builds on Segger. The Segger error is "Failed to connect to target." I updated the devkit firmware with...
1st issue: Tingy91X doesnt build at all with debug -Og enabled: Because of all the strange issues of Thingy91 (nRF9151) and "not to be used in new products) we ordered a couple...
Hi,
I'm trying to build nmea parser, so I have a functionc hecking all nmea sentences and trying to get double value, but I always go bad double value. For example here...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
Dear Nordic company,
I am not able to compile any of my applications I was able to compile. Yesterday, everything works, but today, it doesn't work. I tried older version...
Hi,
I am currently trying to integrate a digital microphone with the I2S peripheral of nRF5340 audio DK. I am accessing the P10 header of the nRF board for the particular...
From the examples of SDK 17.1.0 (I'm Not using Zephyr), I'm trying to connect to a beacon's Generic Access Service, so I can read the characteristic 0x2A00 and then read it...
Hello,
I am trying to measure nRF9151 current using Power Profiler Kit II, running Cellular UDP project on EVK and following the steps in:
https://docs.nordicsemi.com...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
hello all,
I'm fairly new to nRF SDF and its build environment. I browsed a lot of posts but did not find the solution to what is probably a basic misconfiguration error...
Hi, i've setuped Clion to build my porject. I've followed this link . Everything works i'm able to build for my custom board, but in zephyr folder I d'ont see merged.hex file...
