Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
hi
i have NRF51422-QFAA-R V2 ;
i want to know how connect reset pin of my jlink to it?
u see in pic that reset pin is on the swdio;
and also i want use a button to...
Hi,
I am working on the ble_connectivity example in nRF51_SDK_8.1.0_b6ed55f. A make error occurs when building this example.
Would you please tell me how can I fix...
If I understand correctly, a peripheral can distribute data such as UUID, device name, flags, appearance etc. between advertisement and scan response packets. To gather all...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
I am having problems programming PCA10028 using nRFgo Studio.
Note I am using SDK V10.0.0 and IAR EWARM 7.5
Program SoftDevice with s110_nrf51_8.0.0_softdevice.hex ...
My platform is uVision V5.15, running s132 SDK ble_peripheral examples on nRF52 DK.
When compiling the system_nrf52.c in these examples, the error message was shown:
...
Hello everyone, I have an application that i would like to complete and I have most of it finished on Arduino but there are size constraints. Because of that i found the Nordic...
hi, what's the function of the code *(uint32_t *)0x40008C0C = 1 in GPIOTE example of SDK 9.0,
and i know the address of 0x40008000 is TIMER0, and i check the another timer...
Hello,
I a developing a custom application on a custom board with nRF51822 and SDK 10.0. I am also a newbie with BLE, so please bear with me.
I have succeeded in incorporating...
Hello everyone,
I would like to make the following application.
I want to connect a temperature sensor to nRF51822-beacon to broadcast the temperature measurements
...
Hi,
What does the "Enable services" button in the MCP do?
What are the Master Emulator API equivalent command to duplicate the "Enable services" button in the MCP?
...
Two questions:
If I use Nordic's library functions such as app_timer_create() and app_timer_start(), are the timers using the low-power RTC timer running with the...
After I connected a BLE device (HRM sample program on dev kit), I call sd_ble_gap_rssi_start to do a RSSI measurement, it returns error code 6.
Apparently error code 6...
Hi,
I've encountered a problem during development of an application based on ble_app_hrs_rscs_relay.
Everything works fine (I mean concurrent central and peripheral...
