Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Before post this question. I post the MY QUESTION in stackoverflow forum.
but I couldn't find solution.
I know that Nordic board set Bluetooth Low Energy(BLE) multiple...
hi everyone.
we designed a custom board for nrf 51822QFAA chip and we flash the chip by using nrf51 DK debugger with tag-connect cable. when i flash the chip(using keil...
Hello,
I have a serialized app I'm porting to SDK 11 and the S130 SD.
This is an STM32 serialized to an nRF51.
When I call sd_ble_enable(...) for the first time at...
I'm wondering if the BLE is a low power efficient when it has to be always connected to the central device?
How it can be power efficient and the BLE while connected to...
Hello,
I'm looking for details on the nrf52 DAP signals SWDIO and SWDCLK. Such parameters als min. time high, low to Z, clock duty, maximum frequency, minimum frequency etc...
I am working in a custom board which is having nrf1822 chip and I am using Softdevice s130 2.0.1 , SDK 11.0.0, RAM available is 16Kb where soft device uses 5kb of RAM,heap...
I am duty-cycling the radio, so I listen with a timeout and then power off the radio (or transmit) if no packets were received. Currently I am ignoring the address event from...
Hi,
I have programmed s212 soft device onto to NRF52 DK and also programmed ant_broadcast\tx application onto the NRF52 DK. The LED is glowing to indicate that TX is happening...
What is the maximum input voltage for the ADC on the NRF52. I found answer for the NRF51 but nothing definitive on the NRF52.
I have a photocell (or LDR) to sense light ...
Hello,
I am trying to make a basic uart communication between my nordic NRF52 dev board (PCA10040, s132) and my STM32f429ZIT6 discovery board.
NRF52 : I used the example...
Dear Sir,
I and new of development nRF51(256K/16K), I read some sdk docs, but need further information and help.
Would like to save some application information...
Hi,
I'm trying to use the same timeout_handler for two different timers. I use the p_context (as explained here ) to pass a flag to the timeout handler, so that he knows...
At the start of programm, I create a timer_id used the follow code:
app_timer_create(&m_sec_req_timer_id,APP_TIMER_MODE_SINGLE_SHOT,sec_req_timeout_handler);
when the...
Hi, I started using the nRF51422 kit today. Downloaded nRFgo Studio, Master Control Panel, nRF Connect, BLE Sniffer, Wireshark 1.10 (after figuring out that you don't support...
Hai
i am planning to make an iot project with ble for my academics. I am using arduino to control the ble.
I was done a test with blend micro to know its maximum range...
