I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi.
I have a BLE peripheral app for the nRF51822. I'm using SDK 12.1.0 with SD 130 v2.0.1 and gcc. I'm implementing DFU OTA at the moment and I notice there are two builds...
Hi,
I have an old project running on nRF51822, with SoftDevice SDK v8 - S110 mode.
I'm trying to migrate the project to a nRF52832 with SoftDevice SDV v12 - S132 v3 mode...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Hello,
I am facing many communication error with code 1 when using the UART.
Everything is working fine until my client reads long characteristics (in my case it is about...
Hi
We're trying to get the BLE packet size using:-
uint32_t nrfErr;
uint8_t PacketSize;
ble_opt_t opt;
/* Get the extended length BLE option */
nrfErr = sd_ble_opt_get...
Problem:
We trigger HardFaults reproducibly. By manually unwinding the stack we have traced the source of the error back to the TIMER2_IRQHandler in Gazell.
We can see...
Hello,
I am using SDk 11.0.0 and I am trying to integrate the DFU from the heart rate example into the my code, which is based upon the BLE UART (NUS) example. When I run...
i want use s310 in nrf51422 v3 but i cant find it in sdk 12 and i find it in sdk v9 is this correct that ITS IN SDK 9 BUT ITS NOT IN SDK 12 ?
next q is when i use example...
Hi,
For now you propose the "nRF5 IoT SDK v0.9.0 " but mention about the IoT SoftDevice "This SoftDevice is a technology prototype only. Therefore, it should never be used...
Hi,
Our device is slave device with LCD displaying.We need to implement the function as below:
Within range of our slave device, if multiple master device like combined...
First let me explain what I mean by that question, I walked through chapter 17 and was under the impression that there's an "automatic" hardware package wrapper in place to...
In my case LEDs (N<10) would be animated (think pulsing).
My only concern is that the BLE core will limit the possibility to control the LEDs in real time, thus causing...
HI, all Nordic Developer
I know that the S130 soft-driver supports both functions concurrently.
But, I am trying to combine ble_app_beacon and ble_app_uart_c to perform...
