Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
HI all Nordic Developers,
Recently, I am using nRF51 DK as a beacon scanner connected to my laptop (Baudrate: 115200), it works fine to detect the beacon broadcast from...
HI,
I am using development board of BLE nRF52832 battery which you provide CR2032 is support for good battery backups
please give the reasons behind in it?
Hi all,
Is the "to-be-sniffed" advertisement packet allowed to have incorrect CRC, or perhaps a missing CRC? I.e. Is it possible for the sniffer to just display the raw...
Hello,
A problem occurs when i run the DFU over UART on my board.My bootloader project references to nRF51_SDK_9.0.0_2e23562\examples\dfu\bootloader\pca10028\dual_bank_serial_s110...
ANT experts,
I have been looking at the nrf52 implementation of the ANT timestamp (and timesync) features. One thing that is rather puzzling is the fact that the documentation...
Hi. I have two nrf51 dongles that communicate with each other. When I set the transmission power to -30 dB, the range is almost like 15cm, but whe I set it to -20 dB, it has...
nrfutil version 1.5.5
On Linux Mint (Ubuntu like)
in folder nRF5_SDK_12.1.0_0d23e2a/examples/dfu/bootloader_secure/pca10040/armgcc
make
nrfutil pkg generate -...
So I'm trying to upload the application over BLE.
Load the S110 w/ nRFgo Studio.
Load the DFU w/ Keil.
Build the ble_app_hrs example project in s110_with_dfu configuration...
Hello everyone,
I am currently using a nRF52832. I've been trying to use the low power mode with little success. I have been seeing a current draw of about 3.5mA. I would...
I am using an NRF52 dev board to develops a device that connects to an Android and IOS device.
I am unclear on where pairing comes into play with relation to connecting...
Hi in my project I am using nRF5_SDK_11.0.0-2.alpha SDK, s132_nrf52_2.0.0-7.alpha_softdevice. and nrf52 DK board(PC10040).
My issue is, when I run the ble_app_uart example...
Since PStorage has been removed and replaced by FStorage on SDK12, why is PStorage still listed as Experimental in the Documentation? It would appear that if you are removing...
Hello,
I am aware that according to IEEE standards RSSI value that chips return is not officially related to mW/dBm. However the values returned by your chips seem to be...
