Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
nrf52 restart from main() after hit breakpoint and enter [Go] under IAR. It looks like there is some kind timer or watchdog to reset system etc... if stay in breakpoint (...
I have a PMIC in the device that I am building which will eventually take over from the battery. But I have to program the PMIC on startup, using the nRF52. I am trying to...
Hi,
It's the first time I'm developing a piece of code using Nordic SDK, so my question may be absolutely dumb!
We are working on a bl652 (with a nrf52 inside). I just...
I have an application that uses many TWI buses, on many pins of the nRF51. I handle this by initializing/uninitializing a single TWI bus for different transactions. I ran...
in S130 v2.0.0, what is address of central?
i'm using ble central tutorial successfully compiled.
in case of ble peripheral, i can set address whenever running.
so ble...
Dear Nordic Team,
Thanks for supporting.
How to add custom characteristics in standard service ?. I am using Health Thermometer service (HTS). I want to add two custom...
I mounted the chip onto my own PCB, I am not using a devkit, My board is "Wireless-Tag WT51822-S2", it is a module that uses nRF51822-QFAA as (SoC)
I am the ble_app_uart...
With the release of SDK 12.1 the Serialization of S130 is now deprecated.
Within SDK 12.0 the Serialization was supported NOT at all.
When this is true, I have to stay...
I'm trying to stream data in real time from 4 different sensor units to my computer. Each of these sensor units has an NRF52 module that sends data at 50 packets per second...
Hello, I'm south korea student in dongguk univ.
and i want to know how can i send the message on my board(not use the terminal ).
I use the keil uvision4.0, nrf51822...
Hi,
I want to change eddystone_url_data parameter in experimental_ble_app_eddystone (C:\Keil_v5\ARM\PACK\NordicSemiconductor\nRF_Examples\10.0.0\ble_peripheral\experimental_ble_app_eddystone...
Hello, i study the cryption.
First, I'm not good at english...
I use keil uvision4, nrf51822, s110 softdevice
I need check the run-time.
how can i check the runtime...
Hi,
We created a custom board, with the nRF52 and the 32 MHz crystal oscillator according to the reference circuitry.
We use ESB to communicate on RF, and it needs the...
I am new to NRF52832. I want to monitor continuously PIN 3 where I have connected USB to check whether my USB is connected or not. How can I do that. Please reply ASAP.
